Low-Flow Piezoelectric Mist Cooling of an Automotive Radiator: An Experimental Study
Authors
School of Engineering and Technology, University of Technology Sarawak, 96000 Sibu, Sarawak (Malaysia)
School of Engineering and Technology, University of Technology Sarawak, 96000 Sibu, SarCentre for Research of Innovation and Sustainable Development, University of Technology Sarawak, 96000 Sibu, Sarawakwak\ (Malaysia)
School of Engineering and Technology, University of Technology Sarawak, 96000 Sibu, Sarawak (Malaysia)
Article Information
DOI: 10.51584/IJRIAS.2026.11100105
Subject Category: Social science
Volume/Issue: 11/10 | Page No: 1552-1562
Publication Timeline
Submitted: 2026-10-28
Accepted: 2026-11-02
Published: 2026-11-17
Abstract
Modern vehicles are more compact, and fuel cell vehicles (FCVs) are becoming more common. Both trends make radiator cooling harder. There is little space for a larger radiator or more air flow. FCVs produce water as a by-product, and this water could be used to cool the radiator. This study tests piezoelectric-actuated spray cooling on an automotive radiator. Two piezoelectric atomizers were placed in front of a flat-tube radiator with louvered fins. The radiator fan drew the water mist through the core. The coolant was water, in laminar flow (Reynolds number of about 195 to 270). The heating power was 2000, 2500 or 3500 W, which gave coolant inlet temperatures of 41.5 to 61.1 °C. The air velocity was 1.7, 2.0 or 2.3 m/s. The spray flow rate was 0, 5.56 × 10−8 or 1.28 × 10−7 m3/s (3.3 to 7.7 mL/min). Performance was measured by an effective coolant-side Nusselt number. Its uncertainty was 13% to 28%. At the higher spray flow rate, the effective Nusselt number rose by 31.4% to 49.4% over the range of heating power. The enhancement did not rise steadily with heating power. The effect of the spray depended on air velocity. The enhancement was 6.2% at 1.7 m/s and 49.4% at 2.3 m/s. At 1.7 m/s, it was within the measurement uncertainty. From 1.7 to 2.3 m/s, the Nusselt number rose by a factor of 1.54 with the higher spray flow rate and 1.09 without spray. These results suggest that a low-flow piezoelectric spray can improve radiator heat transfer, mainly at higher air velocity. Further tests at engine coolant temperatures and higher coolant flow rates are needed.
Keywords
Spray cooling, Piezoelectric atomizer, Automotive radiator, Convective heat transfer, Heat transfer enhancement
Downloads
References
1. Abdullah, M., & Zoynal Abedin, M. (2024). Recent development of combined heat transfer performance for engine systems: A comprehensive review. Results in Surfaces and Interfaces, 15, 100212. https://doi.org/10.1016/j.rsurfi.2024.100212 [Google Scholar] [Crossref]
2. Bhuiyan, A. A., & Islam, A. K. M. S. (2016). Thermal and hydraulic performance of finned-tube heat exchangers under different flow ranges: A review on modeling and experiment. International Journal of Heat and Mass Transfer, 101, 38–59. https://doi.org/10.1016/j.ijheatmasstransfer.2016.05.022 [Google Scholar] [Crossref]
3. Singh, H., Ting, D. S.-K., Reader, G., Eshtiaghi, N., Ichiyanagi, M., & Suzuki, T. (2024). Experimental investigation of thermal performance of novel finned radiators for automotive cooling system. Journal of Thermal Science, 33(5), 1726–1743. https://doi.org/10.1007/s11630-024-1992-2 [Google Scholar] [Crossref]
4. Huong, N. H., Ting, T. W., Toh, L. K. L., & Ngu, H. J. (2023). Experimental study on convective heat transfer enhancement of automotive radiator with graphene-nanoplatelet suspension. Journal of Advanced Research in Fluid Mechanics and Thermal Sciences, 101(2), 60–72. https://doi.org/10.37934/arfmts.101.2.6072 [Google Scholar] [Crossref]
5. Muthuram, N., Kanchan, B. K., & Ajith Kumar, K. U. (2024). Improving engine cooling performance through slotted fin design: A steady-state thermal analysis study. Journal of Heat and Mass Transfer Research, 11(2), 211–224. https://doi.org/10.22075/JHMTR.2024.32559.1502 [Google Scholar] [Crossref]
6. Toh, L. K. L., & Ting, T. W. (2024). Numerical simulation of graphene-nanoplatelet nanofluid convection in millimeter-sized automotive radiator. CFD Letters, 16(6), 32–52. https://doi.org/10.37934/cfdl.16.6.3252 [Google Scholar] [Crossref]
7. Tawalbeh, M., Alarab, S., Al-Othman, A., & Javed, R. M. N. (2022). The operating parameters, structural composition, and fuel sustainability aspects of PEM fuel cells: A mini review. Fuels, 3(3), 449–474. https://doi.org/10.3390/fuels3030028 [Google Scholar] [Crossref]
8. Wagenblast, M., Pollak, M., Trägner, J., Heinke, S., Tegethoff, W., Köhler, J., & Swoboda, J. (2022). Design and analysis of a spray cooling system for a heavy-duty fuel cell truck (SAE Technical Paper 2022-01-5054). SAE International. https://doi.org/10.4271/2022-01-5054 [Google Scholar] [Crossref]
9. Ebadian, M. A., & Lin, C. X. (2011). A review of high-heat-flux heat removal technologies. Journal of Heat Transfer, 133(11), 110801. https://doi.org/10.1115/1.4004340 [Google Scholar] [Crossref]
10. Kiyama, Y., Tominaga, Y., Kanda, T., Suzumori, K., Kishi, T., Yamada, Y., & Seno, N. (2012). Evaluation of generated micro droplets using micropore plates oscillated by ultrasonic torsional transducers. Sensors and Actuators A: Physical, 185, 92–100. https://doi.org/10.1016/j.sna.2012.08.007 [Google Scholar] [Crossref]
11. Chen, H., Cheng, W.-L., Peng, Y.-H., Zhang, W.-W., & Jiang, L.-J. (2016). Experimental study on optimal spray parameters of piezoelectric atomizer based spray cooling. International Journal of Heat and Mass Transfer, 103, 57–65. https://doi.org/10.1016/j.ijheatmasstransfer.2016.07.037 [Google Scholar] [Crossref]
12. Soriano, G. E., Zhang, T., & Alvarado, J. L. (2014). Study of the effects of single and multiple periodic droplet impingements on liquid film heat transfer. International Journal of Heat and Mass Transfer, 77, 449–463. https://doi.org/10.1016/j.ijheatmasstransfer.2014.04.075 [Google Scholar] [Crossref]
13. Hsieh, S.-S., Hsu, Y.-F., & Wang, M.-L. (2014). A microspray-based cooling system for high powered LEDs. Energy Conversion and Management, 78, 338–346. https://doi.org/10.1016/j.enconman.2013.10.066 [Google Scholar] [Crossref]
14. Lu, C.-F., Yang, J.-C., Chen, C.-J., & Fu, C.-C. (2010). Low power micro spray cooling system. In 2010 5th International Microsystems Packaging Assembly and Circuits Technology Conference (pp. 1–4). IEEE. https://doi.org/10.1109/IMPACT.2010.5699528 [Google Scholar] [Crossref]
15. Hsieh, S.-S., Huang, C.-F., & Lu, Y.-M. (2020). Water spray heat transfer through a piezoelectric atomizer with a single-hole micronozzle. Journal of Mechanical Science and Technology, 34(8), 3427–3436. https://doi.org/10.1007/s12206-020-0735-x [Google Scholar] [Crossref]
16. Kim, J. (2007). Spray cooling heat transfer: The state of the art. International Journal of Heat and Fluid Flow, 28(4), 753–767. https://doi.org/10.1016/j.ijheatfluidflow.2006.09.003 [Google Scholar] [Crossref]
17. Kandlikar, S. G., & Bapat, A. V. (2007). Evaluation of jet impingement, spray and microchannel chip cooling options for high heat flux removal. Heat Transfer Engineering, 28(11), 911–923. https://doi.org/10.1080/01457630701421703 [Google Scholar] [Crossref]
18. Liang, G., & Mudawar, I. (2017). Review of spray cooling – Part 1: Single-phase and nucleate boiling regimes, and critical heat flux. International Journal of Heat and Mass Transfer, 115, 1174–1205. https://doi.org/10.1016/j.ijheatmasstransfer.2017.06.029 [Google Scholar] [Crossref]
19. Martínez, P., Ruiz, J., Martín, Í., & Lucas, M. (2020). Experimental study of an ultrasonic mist generator as an evaporative cooler. Applied Thermal Engineering, 181, 116057. https://doi.org/10.1016/j.applthermaleng.2020.116057 [Google Scholar] [Crossref]
20. Ahmed, F., Ramana, A. S., & Jayakumar, K. (2025). Experimental study on adiabatic pre-cooling systems for air cooled condensers in hot and humid climates. Scientific Reports, 15(1), 4933. https://doi.org/10.1038/s41598-024-82863-0 [Google Scholar] [Crossref]
21. Bop, I., & Dieng, B. (2024). An experimental investigation on the role of the operating time of the mist device on the thermal performances of a water-sprayed air-cooled condenser and on the energy consumption of the cooling system. International Journal of Thermofluids, 24, 100956. https://doi.org/10.1016/j.ijft.2024.100956 [Google Scholar] [Crossref]
22. Park, H., Roh, J., Oh, K. C., Cho, H., & Kim, J. (2022). Modeling and optimization of water mist system for effective air-cooled heat exchangers. International Journal of Heat and Mass Transfer, 184, 122297. https://doi.org/10.1016/j.ijheatmasstransfer.2021.122297 [Google Scholar] [Crossref]
23. Su, C.-Q., Wang, S., Liu, X., Tao, Q., & Wang, Y.-P. (2022). Experimental and numerical investigation on spray cooling of radiator in fuel cell vehicle. Energy Reports, 8, 1283–1294. https://doi.org/10.1016/j.egyr.2021.11.174 [Google Scholar] [Crossref]
24. Park, U. J., Kwon, S. B., Choi, K. J., Lee, G. W., & Oh, D. S. (2024). A preliminary study on the evaporative cooling system for FCEV (SAE Technical Paper 2024-01-2406). SAE International. https://doi.org/10.4271/2024-01-2406 [Google Scholar] [Crossref]
25. Mohamed Souby, M., Prabakaran, R., & Kim, S. C. (2025). Nozzle spray-cooling coupled PEMFC stack radiator: Thermal-hydraulic performance and integrated correlations. Energy, 321, 135517. https://doi.org/10.1016/j.energy.2025.135517 [Google Scholar] [Crossref]
26. Zeng, R., Kang, H., Umar, M., Liang, X., & Zhao, Y.-N. (2025). Design and thermal management study of fuel cell spray cooling system. Applied Thermal Engineering, 270, 126271. https://doi.org/10.1016/j.applthermaleng.2025.126271 [Google Scholar] [Crossref]
27. Bergman, T. L., Lavine, A. S., Incropera, F. P., & DeWitt, D. P. (2017). Fundamentals of heat and mass transfer (8th ed.). Wiley. [Google Scholar] [Crossref]
28. Hussein, A. M., Bakar, R. A., & Kadirgama, K. (2014). Study of forced convection nanofluid heat transfer in the automotive cooling system. Case Studies in Thermal Engineering, 2, 50–61. https://doi.org/10.1016/j.csite.2013.12.001 [Google Scholar] [Crossref]
Metrics
Views & Downloads
Similar Articles
- The Impact of Ownership Structure on Dividend Payout Policy of Listed Plantation Companies in Sri Lanka
- Urban Sustainability in North-East India: A Study through the lens of NER-SDG index
- Performance Assessment of Predictive Forecasting Techniques for Enhancing Hospital Supply Chain Efficiency in Healthcare Logistics
- The Fractured Self in Julian Barnes' Postmodern Fiction: Identity Crisis and Deflation in Metroland and the Sense of an Ending
- Impact of Flood on the Employment, Labour Productivity and Migration of Agricultural Labour in North Bihar