Development and Performance Evaluation of Sustainable Composite Wall Cladding Integrating Recycled PET, Waste Tire Steel Fibers, and Rice Husk Ash (RHA)

The accumulation of polyethylene terephthalate (PET) waste, vehicle tires, and rice husk ash (RHA) presents a critical environmental challenge in developing countries. This study explores a sustainable composite wall cladding that integrates recycled PET as a polymeric binder, river sand, waste tire steel fibers (SFs), and RHA fillers. Material characterization (XRF, thermal analysis) confirmed a high silica content in RHA (91%) and sand (82%), with a PET melting threshold of 240-255°C. The composites were fabricated through a hot-mixing process at 250°C, while maintaining constant PET and SFs content, systematically varying the RHA-to-sand substitution ratio from 0% to 20% by weight. The experimental results demonstrated that enhancing RHA concentration typically reduced density (from 2.469g/cm3 to 1.495 g/cm3) due to low specific gravity of the ash. While water absorption slightly enhanced (1.8% to 3.12%), values maintained the ‘’Vitreous’’ range of ASTM C373. Compressive strength exhibited an optimal peak of 24.1 MPa at a 12.5% RHA concentration, supported by impact energy absorption (3.29 Joules) without visible damage. The study reveals an optimal mix design of 12.2% RHA and 36.6% sand, demonstrating that RHA serves as an effective secondary reinforcement up to a critical threshold before binder starvation occurs. This research establishes a technical framework for circular economy practices in Tanzania, contributing to a high-performance, low-cost alternative to traditional cladding materials.

Repurposed PET, Rice husk ash, Recycled steel fibers, Sustainability

1. Ahmat, T., Djomou Djonga, P. N., Hambate Gomdje, V., & Kamdoum Noukelack, S. (2021). Mechanical Properties and Chemical Stability of Bathroom Wall Composites Manufactured from Recycled Polyethylene Terephthalate (PET) Mixed with Cocoa Hulls Powder. Journal of Advanced Chemical Sciences, 7(4), 751–755. https://doi.org/10.30799/jacs.243.21070402 [Google Scholar] [Crossref]

2. Ahmed, W., Lim, C. W., & Akbar, A. (2022). Influence of Elevated Temperatures on the Mechanical Performance of Sustainable-Fiber-Reinforced Recycled Aggregate Concrete: A Review. Buildings, 12(4), 487. https://doi.org/10.3390/buildings12040487 [Google Scholar] [Crossref]

3. Aisheh, Y. I. A., Atrushi, D. S., Akeed, M. H., Qaidi, S., & Tayeh, B. A. (2022). Influence of polypropylene and steel fibers on the mechanical properties of ultra-high-performance fiber-reinforced geopolymer concrete. Case Studies in Construction Materials, 17, e01234. https://doi.org/10.1016/j.cscm.2022.e01234 [Google Scholar] [Crossref]

4. Amran, M., Fediuk, R., Murali, G., Vatin, N., Karelina, M., Ozbakkaloglu, T., Krishna, R. S., Sahoo, A. K., Das, S. K., & Mishra, J. (2021). Rice Husk Ash-Based Concrete Composites: A Critical Review of Their Properties and Applications. Crystals, 11(2), 168. https://doi.org/10.3390/cryst11020168 [Google Scholar] [Crossref]

5. Awolusi, T., Oguntayo, D., Deifalla, A. F., Babalola, E., Natie, F., Aladegboye, O., & Azab, M. (2023). Utilization of Bitumen Modified with Pet Bottles as an Alternative Binder for the Production of Paving Blocks. Civil Engineering Journal, 9(1), 104–113. https://doi.org/10.28991/CEJ-2023-09-01-08 [Google Scholar] [Crossref]

6. Bamigboye, G. O., Ngene, B. U., Ademola, D., & Jolayemi, J. K. (2019). Experimental Study on the Use of Waste Polyethylene Terephthalate (PET) and River Sand in Roof Tile Production. Journal of Physics: Conference Series, 1378(4), 042105. https://doi.org/10.1088/1742-6596/1378/4/042105 [Google Scholar] [Crossref]

7. Channa, M. Y., Anwar, J., Kalsoom, R., & Abidi, S. H. I. (2024). Qualitative analysis of rivers sand sources (Silica sand, Ravi River sand, Indus River sand, and Jhelum River sand) for metal casting: A comparative study. Engineering Research Express, 6(3), 035435. https://doi.org/10.1088/2631-8695/ad7cc2 [Google Scholar] [Crossref]

8. Da Silva, T. R., De Azevedo, A. R. G., Cecchin, D., Marvila, M. T., Amran, M., Fediuk, R., Vatin, N., Karelina, M., Klyuev, S., & Szelag, M. (2021). Application of Plastic Wastes in Construction Materials: A Review Using the Concept of Life-Cycle Assessment in the Context of Recent Research for Future Perspectives. Materials, 14(13), 3549. https://doi.org/10.3390/ma14133549 [Google Scholar] [Crossref]

9. Dalvand, A., & Ahmadi, M. (2021). Impact failure mechanism and mechanical characteristics of steel fiber reinforced self-compacting cementitious composites containing silica fume. Engineering Science and Technology, an International Journal, 24(3), 736–748. https://doi.org/10.1016/j.jestch.2020.12.016 [Google Scholar] [Crossref]

10. Emah, J. B., Edema, A., Ekong, S. A., Oyegoke, D. A., Robert, U., & Fasuyi, F. O. (2024). Thermophysical, strength, and electrical properties of clay modified with groundnut shell ash for building purposes. Journal of Sustainable Construction Materials and Technologies, 9(4), 335–345. https://doi.org/10.47481/jscmt.1600562 [Google Scholar] [Crossref]

11. Ezenkwa, O. E., Hassan, A., & Samsudin, S. A. (2022). Mechanical properties of rice husk and rice husk ash filled maleated polymers compatibilized polypropylene composites. Journal of Applied Polymer Science, 139(9), 51702. https://doi.org/10.1002/app.51702 [Google Scholar] [Crossref]

12. Farhan, K. Z., Johari, M. A. M., & Demirboğa, R. (2021). Impact of fiber reinforcements on properties of geopolymer composites: A review. Journal of Building Engineering, 44, 102628. https://doi.org/10.1016/j.jobe.2021.102628 [Google Scholar] [Crossref]

13. Faried, A. S., Mostafa, S. A., Tayeh, B. A., & Tawfik, T. A. (2021). The effect of using nano rice husk ash of different burning degrees on ultra-high-performance concrete properties. Construction and Building Materials, 290, 123279. https://doi.org/10.1016/j.conbuildmat.2021.123279 [Google Scholar] [Crossref]

14. Finnerty, J., Rowe, S., Howard, T., Connolly, S., Doran, C., Devine, D. M., Gately, N. M., Chyzna, V., Portela, A., Bezerra, G. S. N., McDonald, P., & Colbert, D. M. (2023). Effect of Mechanical Recycling on the Mechanical Properties of PLA-Based Natural Fiber-Reinforced Composites. Journal of Composites Science, 7(4), 141. https://doi.org/10.3390/jcs7040141 [Google Scholar] [Crossref]

15. Guclu, M., Alkan Göksu, Y., Özdemir, B., Ghanbari, A., & Nofar, M. (2022). Thermal Stabilization of Recycled PET Through Chain Extension and Blending with PBT. Journal of Polymers and the Environment, 30(2), 719–727. https://doi.org/10.1007/s10924-021-02238-8 [Google Scholar] [Crossref]

16. Hamzah, A. F., & Alkhafaj, R. M. (2022). An investigation of manufacturing technique and characterization of low-density polyethylene waste base bricks. Materials Today: Proceedings, 61, 724–733. https://doi.org/10.1016/j.matpr.2021.08.318 [Google Scholar] [Crossref]

17. Hossain, M. T., Shahid, M. A., Mahmud, N., Darda, M. A., & Samad, A. B. (2024). Techniques, applications, and prospects of recycled polyethylene terephthalate bottle: A review. Journal of Thermoplastic Composite Materials, 37(3), 1268–1286. https://doi.org/10.1177/08927057231190065 [Google Scholar] [Crossref]

18. Jawaid, M., Singh, B., Kian, L. K., Zaki, S. A., & Radzi, A. M. (2023). Processing techniques on plastic waste materials for construction and building applications. Current Opinion in Green and Sustainable Chemistry, 40, 100761. https://doi.org/10.1016/j.cogsc.2023.100761 [Google Scholar] [Crossref]

19. Jittin, V., Bahurudeen, A., & Ajinkya, S. D. (2020). Utilisation of rice husk ash for cleaner production of different construction products. Journal of Cleaner Production, 263, 121578. https://doi.org/10.1016/j.jclepro.2020.121578 [Google Scholar] [Crossref]

20. Karedla, A. B., Schuster, J., & Shaik, Y. P. (2024). Possibility of Making Plastic Roof Tiles from Waste Plastic, Sand, and Fly Ash. Construction Materials, 4(3), 597–610. https://doi.org/10.3390/constrmater4030032 [Google Scholar] [Crossref]

21. Kumar, A., & Bedi, R. (2025). Mechanical and durability properties of sustainable composites derived from recycled polyethylene terephthalate and enhanced with natural fibers: A comprehensive review. https://doi.org/10.18149/MPM.5312025_10 [Google Scholar] [Crossref]

22. Kumavat, H. R., Chandak, N. R., & Patil, I. T. (2021). Factors influencing the performance of rebound hammer used for non-destructive testing of concrete members: A review. Case Studies in Construction Materials, 14, e00491. https://doi.org/10.1016/j.cscm.2021.e00491 [Google Scholar] [Crossref]

23. Mache, E., Nthiga, E., & Muthakia, G. K. (2023). Formulation and characterization of floor tile composite derived from Polyethylene Terephthalate waste and sand. [Google Scholar] [Crossref]

24. Mashaan, N., Chegenizadeh, A., & Nikraz, H. (2021). Laboratory Properties of Waste PET Plastic-Modified Asphalt Mixes. Recycling, 6(3), 49. https://doi.org/10.3390/recycling6030049 [Google Scholar] [Crossref]

25. Ministry of Works (MoW). (2000). Laboratory testing manual. Novum Grafisk AS, Skjetten Norway. [Google Scholar] [Crossref]

26. Muringayil Joseph, T., Azat, S., Ahmadi, Z., Moini Jazani, O., Esmaeili, A., Kianfar, E., Haponiuk, J., & Thomas, S. (2024). Polyethylene terephthalate (PET) recycling: A review. Case Studies in Chemical and Environmental Engineering, 9, 100673. https://doi.org/10.1016/j.cscee.2024.100673 [Google Scholar] [Crossref]

27. Naderi Kalali, E., Lotfian, S., Entezar Shabestari, M., Khayatzadeh, S., Zhao, C., & Yazdani Nezhad, H. (2023). A critical review of the current progress of plastic waste recycling technology in structural materials. Current Opinion in Green and Sustainable Chemistry, 40, 100763. https://doi.org/10.1016/j.cogsc.2023.100763 [Google Scholar] [Crossref]

28. Nikolić, E., Delić-Nikolić, I., Jovičić, M., Miličić, L., & Mijatović, N. (2023). Recycling and Reuse of Building Materials in a Historical Landscape—Viminacium Natural Brick (Serbia). Sustainability, 15(3), 2824. https://doi.org/10.3390/su15032824 [Google Scholar] [Crossref]

29. Nurazzi, N. M., Asyraf, M. R. M., Fatimah Athiyah, S., Shazleen, S. S., Rafiqah, S. A., Harussani, M. M., Kamarudin, S. H., Razman, M. R., Rahmah, M., Zainudin, E. S., Ilyas, R. A., Aisyah, H. A., Norrrahim, M. N. F., Abdullah, N., Sapuan, S. M., & Khalina, A. (2021). A Review on Mechanical Performance of Hybrid Natural Fiber Polymer Composites for Structural Applications. Polymers, 13(13), 2170. https://doi.org/10.3390/polym13132170 [Google Scholar] [Crossref]

30. Nurhayati, C., & Susanto, T. (2020). The Effects of Rice Husk Ashes Filled Recycled Polyethylene Composites towards Physical, Mechanical Properties and Its Degradation Characteristics. IOP Conference Series: Materials Science and Engineering, 924(1), 012029. https://doi.org/10.1088/1757-899X/924/1/012029 [Google Scholar] [Crossref]

31. Omosebi, T. O., & Abass, N. F. (2021). Polymer tiles from polyethylene terephthalate (PET) wastes and fly ash: Mechanical properties and durability. F1000Research, 10, 1139. https://doi.org/10.12688/f1000research.53514.1 [Google Scholar] [Crossref]

32. Peter Laurian, Dr Duwa Hamisi Chengula, & Dr Patrice Nyangi. (2024). The use of waste Polyethylene Terephthalate (PET) plastics for wall cladding materials in Mbeya Tanzania. Engineering Science & Technology Journal, 5(10), 2897–2910. https://doi.org/10.51594/estj.v5i10.1633 [Google Scholar] [Crossref]

33. Rojas-Valencia, M. N., Rivas-Torres, B. I., Fernández-Rojas, D. Y., & Gómez-Soberón, J. M. (2022). Recovery of Mixtures of Construction Waste, PET and Sugarcane Bagasse for the Manufacture of Partition Blocks. Materials, 15(19), 6836. https://doi.org/10.3390/ma15196836 [Google Scholar] [Crossref]

34. Sahu, P., & Gupta, M. (2022). Water absorption behavior of cellulosic fibres polymer composites: A review on its effects and remedies. Journal of Industrial Textiles, 51(5_suppl), 7480S-7512S. https://doi.org/10.1177/1528083720974424 [Google Scholar] [Crossref]

35. Selvaranjan, K., Gamage, J. C. P. H., De Silva, G. I. P., & Navaratnam, S. (2021). Development of sustainable mortar using waste rice husk ash from rice mill plant: Physical and thermal properties. Journal of Building Engineering, 43, 102614. https://doi.org/10.1016/j.jobe.2021.102614 [Google Scholar] [Crossref]

36. Sharma, D., Moondra, N., Bharatee, R. K., Nema, A., Sweta, K., Yadav, M. K., & Maurya, N. S. (2024). Processing and Recycling of Plastic Wastes for Sustainable Material Management. In J. Parameswaranpillai & K. Deshmukh (Eds.), Plastic Waste Management (1st ed., pp. 89–116). Wiley. https://doi.org/10.1002/9783527842209.ch4 [Google Scholar] [Crossref]

37. Sharma, H., Kumar, A., Rana, S., Sahoo, N. G., Jamil, M., Kumar, R., Sharma, S., Li, C., Kumar, A., Eldin, S. M., & Abbas, M. (2023). Critical review on advancements on the fiber-reinforced composites: Role of fiber/matrix modification on the performance of the fibrous composites. Journal of Materials Research and Technology, 26, 2975–3002. https://doi.org/10.1016/j.jmrt.2023.08.036 [Google Scholar] [Crossref]

38. Siddika, A., Mamun, Md. A. A., Alyousef, R., & Mohammadhosseini, H. (2021). State-of-the-art-review on rice husk ash: A supplementary cementitious material in concrete. Journal of King Saud University - Engineering Sciences, 33(5), 294–307. https://doi.org/10.1016/j.jksues.2020.10.006 [Google Scholar] [Crossref]

39. Slezák, E., Ronkay, F., & Bocz, K. (2023). Development of an Engineering Material with Increased Impact Strength and Heat Resistance from Recycled PET. Journal of Polymers and the Environment, 31(12), 5296–5308. https://doi.org/10.1007/s10924-023-02945-4 [Google Scholar] [Crossref]

40. Soni, A., Chakraborty, S., Kumar Das, P., & Kumar Saha, A. (2022). Materials selection of reinforced sustainable composites by recycling waste plastics and agro-waste: An integrated multi-criteria decision-making approach. Construction and Building Materials, 348, 128608. https://doi.org/10.1016/j.conbuildmat.2022.128608 [Google Scholar] [Crossref]

41. Soong, Y.-H. V., Sobkowicz, M. J., & Xie, D. (2022). Recent Advances in Biological Recycling of Polyethylene Terephthalate (PET) Plastic Wastes. Bioengineering, 9(3), 98. https://doi.org/10.3390/bioengineering9030098 [Google Scholar] [Crossref]

42. Tayeh, B. A., Alyousef, R., Alabduljabbar, H., & Alaskar, A. (2021). Recycling of rice husk waste for a sustainable concrete: A critical review. Journal of Cleaner Production, 312, 127734. https://doi.org/10.1016/j.jclepro.2021.127734 [Google Scholar] [Crossref]

43. Vieira, A. P., Toledo Filho, R. D., Tavares, L. M., & Cordeiro, G. C. (2020). Effect of particle size, porous structure and content of rice husk ash on the hydration process and compressive strength evolution of concrete. Construction and Building Materials, 236, 117553. https://doi.org/10.1016/j.conbuildmat.2019.117553 [Google Scholar] [Crossref]

44. Wan, Y., Wang, H., Liu, J., Li, J., Zhou, W., Zhang, J., Liu, X., Song, X., Wang, H., & Huo, P. (2024). Removal of polyethylene terephthalate plastics waste via Co–CeO2 photocatalyst–activated peroxymonosulfate strategy. Chemical Engineering Journal, 479, 147781. https://doi.org/10.1016/j.cej.2023.147781 [Google Scholar] [Crossref]

45. Wen, C., Zhang, P., Wang, J., & Hu, S. (2022). Influence of fibers on the mechanical properties and durability of ultra-high-performance concrete: A review. Journal of Building Engineering, 52, 104370. https://doi.org/10.1016/j.jobe.2022.104370 [Google Scholar] [Crossref]

46. Yatawara, M., & Athukorala, S. (2021). Potential of replacing clay soil by rice husk ash (RHA) in enhancing the properties of compressed earth blocks (CEBs). Environment, Development and Sustainability, 23(3), 3474–3486. https://doi.org/10.1007/s10668-020-00727-9 [Google Scholar] [Crossref]

47. Zeybek, Ö., Özkılıç, Y. O., Çelik, A. İ., Deifalla, A. F., Ahmad, M., & Sabri Sabri, M. M. (2022). Performance evaluation of fiber-reinforced concrete produced with steel fibers extracted from waste tire. Frontiers in Materials, 9, 1057128. https://doi.org/10.3389/fmats.2022.1057128 [Google Scholar] [Crossref]

• A Case Study on the Development and Simulation of a High-Efficiency Flyback Converter for Portable Solar LED Lighting
• Greening the Campus: Stakeholders’ Insights on Sustainability Practices in a Chinese Higher Education Institution
• Malaysia’s Renewable Energy and CO₂ Emissions: ARDL–ECM Evidence with Policy and Managerial Implications
• Waqf within Business Model Framework: A Review and Research Agenda
• Sustainability-Driven Green City Framework and its Impact on Malaysia’s Tourism Industry Development