Electroconductive Tantalum-Based Coatings for Bioelectronic Bone Implants: Fabrication, Characterisation, and Neural Interface Applications

To improve the bioelectrical conductivity, bioactivity, and biocompatibility of titanium implants, an electroconductive tantalum (Ta) coating was fabricated on Ti6Al4V (TC4) substrates via the cold spray technique. Microstructural and phase characterizations were performed using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), and Fourier-Transform Infrared Spectroscopy (FTIR). Four-point probe resistivity, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV) were used to characterize electrical and electrochemical properties relevant to neural interfaces. Mechanical and bioactivity evaluations included tensile adhesion, three-point bending, and Vickers microhardness tests, alongside simulated body fluid (SBF) immersion to assess osteointegration potential. Results show that the cold-sprayed Ta coating exhibits a bulk electrical conductivity of 6.8 × 106 S/m, approximately 40 % that of pure bulk Ta, due to the presence of inter-particle interfaces and porosity. The coating’s impedance at 1 kHz-a frequency range relevant to neural signal transmission was measured at ~8.2 kΩ•cm², indicating favorable charge transfer capability for neural electrode applications. The double-layer capacitance extracted from the EIS Nyquist plots was approximately 2.6 mF/cm², signifying strong electrochemical surface activity. Mechanically, the coatings exhibited an adhesive strength of 10.6 MPa, microhardness of 300 HV0.1, and Young’s modulus of 11.08 GPa, closely matching the modulus of natural cortical bone (10-30 GPa). Bioactivity assessment showed dense apatite layer formation within 14 days of immersion, while electrical stimulation (±100 μA, 1 Hz) significantly enhanced apatite nucleation rates, confirming electro-assisted biomineralization. These findings show improvement in bone-implant integration with emphasis on electrical performance suitable for bioelectronic and neural stimulation implants.

Cold spray, Electroconductive coatings, Tantalum, Neural interface, Bioelectronics, Osteointegration, Impedance

1. Alontseva, D., Azamatov, B., Safarova, Y., Voinarovych, S., & Nazenova, G. (2023). “A Brief Review of Current Trends in the Additive Manufacturing of Orthopedic Implants with Thermal Plasma-Sprayed Coatings to Improve the Implant Surface Biocompatibility”, Coatings, 13(7), p. 1175. [Google Scholar] [Crossref]

2. Argyropoulou, E., Sakellariou, E., Galanis, A., Karampinas, P., Rozis, M., Koutas, K., Tsalimas, G., Vasiliadis, E., Vlamis, J., and Pneumaticos, S. (2024), “Porous Tantalum Acetabular Cups in Primary and Revision Total Hip Arthroplasty: What Has Been the Experience So Far? - A Systematic Literature Review”, Biomedicines, 12(5), p. 959. [Google Scholar] [Crossref]

3. Balla, V. K., Banerjee, S., Bose, S. and Bandyopadhyay, A. (2010a), “Direct Laser Processing of a Tantalum Coating on Titanium for Bone Replacement Structures”, Acta Biomaterialia, 6(6), pp. 2329– 2334. [Google Scholar] [Crossref]

4. Balla, V. K., Bodhak, S., Bose, S. and Bandyopadhyay, A. (2010b), “Porous Tantalum Structures for Bone Implants: Fabrication, Mechanical and in Vitro Biological Properties”. Acta Biomaterialia, 6(8), pp. 3349–3359. [Google Scholar] [Crossref]

5. Baltatu, M. S., Vizureanu, P., Sandu, A. V., Solcan, C., Hritcu, L. D. and Spataru, M. C. (2023) “Research Progress of Titanium-Based Alloys for Medical Devices”, Biomedicines, 11(11), p. 2997. [Google Scholar] [Crossref]

6. Chen, P.-Y., McKittrick, J. and Meyers, M. A. (2012) “Biological Materials: Functional Adaptations and Bioinspired Designs. Progress in Materials Science, 57(8), pp. 1492–1704. [Google Scholar] [Crossref]

7. Chen, Q. and Thouas, G. A. (2015) “Metallic Implant Biomaterials”. Materials Science and Engineering: R: Reports, 87, pp. 1–57. [Google Scholar] [Crossref]

8. Delloro, F., Jeandin, M., Jeulin, D., Proudhon, H., Faessel, M., Bianchi, L., Meillot, E. and Helfen, L. (2017) “A Morphological Approach to the Modelling of the Cold Spray Process”, Journal of Thermal Spray Technology, 26(8), pp. 1838–1850. [Google Scholar] [Crossref]

9. Forero-Sandoval, I. Y., Franco-Bacca, A. P., Cervantes-Álvarez, F., Gómez-Heredia, C. L., Ramírez-Rincón, J. A., Ordonez-Miranda, J. and Alvarado-Gil, J. J. (2022), “Electrical and Thermal Percolation in Two-Phase Materials: A Perspective”, Journal of Applied Physics, 131(23). [Google Scholar] [Crossref]

10. Gartner, F., Stoltenhoff, T., Schmidt, T. and Kreye, H. (2006) “The Cold Spray Process and Its Potential for Industrial Applications”. Journal of Thermal Spray Technology, 15(2), pp. 223–232. [Google Scholar] [Crossref]

11. Gere, J. M. and Timoshenko, S. (2009) Mechanics of Materials (CL-Engineering), 402 p. [Google Scholar] [Crossref]

12. Xinting, K., Yaning, L., Guangzhong, L. and Ye, L., (2017), “Effect of Sintering Temperature on Properties of Tantalum Porous Materials”, Rare Metal Materials and Engineering, 46(4), pp. 1092-1096. [Google Scholar] [Crossref]

13. Koivuluoto, H., Honkanen, M. and Vuoristo, P. (2010) “Cold-Sprayed Copper and Tantalum Coatings - Detailed FESEM and TEM Analysis”. Surface and Coatings Technology, 204(15), pp. 2353–2361. [Google Scholar] [Crossref]

14. Kokubo, T. and Takadama, H. (2006) “How Useful is SBF in Predicting in Vivo Bone Bioactivity?” Biomaterials, 27(15), pp. 2907–2915. [Google Scholar] [Crossref]

15. Kumar, S., Vidyasagar, V., Jyothirmayi, A. and Joshi, S. V. (2016) “Effect of Heat Treatment on Mechanical Properties and Corrosion Performance of Cold-Sprayed Tantalum Coatings”. Journal of Thermal Spray Technology, 25(4), pp. 745–756. [Google Scholar] [Crossref]

16. Lei, P., Qian, H., Zhang, T., Lei, T., Hu, Y., Chen, C. and Zhou, K. (2022), “Porous Tantalum Structure Integrated on Ti6Al4V Base by Laser Powder Bed Fusion for Enhanced Bony-Ingrowth Implants: In Vitro and In Vivo Validation”, Bioactive Materials, 7, pp. 3-13. [Google Scholar] [Crossref]

17. Liu, A., Wang, C., Zhao, Z., Zhu, R., Deng, S., Zhang, S., Ghorbani, F., Ying, T., Yi, C., and Li, D. (2025), “Progress of Porous Tantalum Surface-Modified Biomaterial Coatings in Bone Tissue Engineering”, Journal of Materials Science: Materials in Medicine, 36(1), pp. 1–14. [Google Scholar] [Crossref]

18. Loi, F., Córdova, L. A., Pajarinen, J., Lin, T. H., Yao, Z. and Goodman, S. B. (2016), “Inflammation, Fracture and Bone Repair”. Bone, 86, pp. 119–130. [Google Scholar] [Crossref]

19. Melcher, F., Graupner, T., Gäbler, H. E., Sitnikova, M., Oberthür, T., Gerdes, A., Badanina, E. and Chudy, T. (2017), “Mineralogical and Chemical Evolution of Tantalum-(Niobium–Tin) Mineralisation in Pegmatites and Granites. Part 2: Worldwide Examples (Excluding Africa) and an Overview of Global Metallogenetic Patterns”, Ore Geology Reviews, 89, pp. 946–987. [Google Scholar] [Crossref]

20. Meyers, M. A., McKittrick, J. and Chen, P. Y. (2013), “Structural Biological Materials: Citical Mechanics–Materials Connections”. Science, 339(6121), pp. 773–779. [Google Scholar] [Crossref]

21. Moridi, A., Hassani-Gangaraj, S. M., Guagliano, M. and Dao, M. (2014), “Cold Spray Coating: Review of Material Systems and Future Perspectives”. Surface Engineering, 30(6), pp. 369–395. [Google Scholar] [Crossref]

22. Neu, R., Maier, H., Böswirth, B., Elgeti, S., Greuner, H., Hunger, K., Kondas, J. and von Müller, A. (2023) “Investigations on Cold Spray Tungsten/Tantalum Coatings for Plasma Facing Applications”, Nuclear Materials and Energy, 34, p. 101343. [Google Scholar] [Crossref]

23. Oryan, A., Alidadi, S., Moshiri, A. and Maffulli, N. (2014), “Bone Regenerative Medicine: Classic Options, Novel Strategies, and Future Directions”. Journal of Orthopaedic Surgery and Research, 9(1), p. 18. [Google Scholar] [Crossref]

24. Papyrin, A., Kosarev, V., Klinkov, S., Alkhimov, A. and Fomin, V. M. (2006), Cold Spray Technology, 1st Edn, Elsevier, The Netherlands, pp. 27–28. [Google Scholar] [Crossref]

25. Schmidt, T., Gärtner, F., Assadi, H. and Kreye, H. (2006), “Development of a Generalized Parameter Window for Cold Spray Deposition”. Acta Materialia, 54(3), pp. 729–742. [Google Scholar] [Crossref]

26. Shabalin, I. L. (2014), Ultra-High Temperature Materials. Springer, New York, NY, USA. pp. 237–531. [Google Scholar] [Crossref]

27. Wei, S., Bangchao, Y., Xuanhong, Z., Jianhua, M., Qifeng, P. and Xingwei, W. (2015), “Effect of Sintering Time on the Microstructure of Porous Tantalum”. Rare Metal Materials and Engineering, 44(2), pp. 319–322. [Google Scholar] [Crossref]

28. Simchi, A., Tamjid, E., Pishbin, F. and Boccaccini, A. R. (2011), “Recent Progress in Inorganic and Composite Coatings with Bactericidal Capability for Orthopaedic Applications”. Nanomedicine: Nanotechnology, Biology and Medicine, 7(1), pp. 22–39. [Google Scholar] [Crossref]

29. Takana, H., Li, H., Ogawa, K., Kuriyagawa, T. and Nishiyama, H. (2010), “Computational and Experimental Studies on Cavity Filling Process by Cold Gas Dynamic Spray”, Journal of Fluids Engineering – Transactions of the ASME, 132(2), 021302. [Google Scholar] [Crossref]

30. Van Bael, S., Chai, Y. C., Truscello, S., Moesen, M., Kerckhofs, G., Van Oosterwyck, H., Kruth, J. P. and Schrooten, J. J. A. B. (2012), “The Effect of Pore Geometry on the In Vitro Biological Behaviour of Human Periosteum-Derived Cells Seeded on Selective Laser-Melted Ti6Al4V Bone Scaffolds”, Acta Biomaterialia, 8(7), pp. 2824–2834. [Google Scholar] [Crossref]

31. Vilardell, A. M., Cinca, N., Concustell, A., Dosta, S., Cano, I. G. and Guilemany, J. M. (2015), “Cold Spray as an Emerging Technology for Biocompatible and Antibacterial Coatings: State of the Art”, Journal of Materials Science, 50(13), pp. 4441–4462. [Google Scholar] [Crossref]

32. Nikolova, M. P. and Tzvetkov, I. (2025), “Influence of Deposition Temperature on Microstructure and Propertie of Tantalum Oxide Sputtered Coatings. Materials”, 18(9), p.1895. [Google Scholar] [Crossref]

33. Wang, X., Liu, W., Yu, X., Wang, B., Xu, Y., Yan, X. and Zhang, X. (2022), “Advances in Surface Modification of Tantalum and Porous Tantalum for Rapid Osseointegration: A Thematic Review”, Frontiers in Bioengineering and Biotechnology, 10, p. 983695. [Google Scholar] [Crossref]

34. Xiong, Y., Zhuang, W., and Zhang, M. (2015), “Effect of Thickness of Cold Sprayed Aluminium Alloy Coating on the Adhesive Bond Strength with an Aluminium Alloy Substrate”. Surface and Coatings Technology, 270, pp. 259–265. [Google Scholar] [Crossref]

• The Impact Of UI/UX Design on User Trust and Task Completion in Civic Tech Platforms
• Solar Cell Photovoltaic Model Shell Sp 75
• Development of an Intelligent Traffic Management System to Address Visibility Obstruction at Urban Intersections: A Case Study of Ibadan Metropolis
• Optimum Placement of Facts Devices on an Interconnected Power Systems Using Particle Swarm Optimisation Technique
• Assessing Construction Transformation and Implication on Future Production Flow System