Performance Evaluation of Ceno-TiO₂/Al Electrodes in Continuous Electrocoagulation of Automobile Wash Wastewater

The increasing generation of fly ash from coal-based power plants poses significant environmental challenges, necessitating sustainable utilization strategies. This study explores the use of modified fly ash cenospheres as eco-friendly and cost-effective materials for wastewater treatment, particularly automobile wash effluent containing high levels of COD, suspended solids, oil, and grease. Various modifications of cenospheres, including chitosan coating and TiO₂ functionalization, were synthesized and characterized using SEM, EDAX, AFM, XRD, FTIR, and surface area analysis. Electrochemical behavior and physicochemical properties were also evaluated.
The performance of modified cenospheres was assessed through electrocoagulation and jar test experiments under optimized conditions. Among the samples, chitosan cross-linked cenosphere (CCP) exhibited superior removal efficiency, faster sedimentation, and higher floc formation compared to other variants. Maximum pollutant removal was achieved at optimized pH and contact time. The findings demonstrate that modified cenospheres, particularly CCP, are effective and sustainable materials for wastewater treatment, offering a promising solution for small-scale industrial applications.

scanning electron microscopy (SEM), energy dispersive

1. Blissett, RS & Rowson, NA 2012, ‘A review of the multi-component utilisation of coal fly ash’, Fuel, vol. 97, no. 7, pp. 1–23 [Google Scholar] [Crossref]

2. Deepthi, MV, Sharma, M, Sailaja, RRN, Anantha, P, Sampathkumaran, P & Seetharamu, S 2010, ‘Mechanical and thermal characteristics of high density polyethylene-fly ash Cenospheres composites’, Materials and Design, vol. 31, no. 4, pp. 2051–2060. [Google Scholar] [Crossref]

3. Gao, X, Dai, Y, Zhang, Y, Zhai, X & Fu, F 2016, ‘Effective dye removal from waste water using a novel low-cost NaOH-modified fly ash’, Clays and Clay Minerals, vol. 64, no. 6, pp. 695–705. [Google Scholar] [Crossref]

4. Grace, MA, Clifford, E & Healy, MG 2016, ‘The potential for the use of waste products from a variety of sectors in water treatment processes’, Journal of Cleaner Production, vol. 137, no. 28, pp. 788–802. [Google Scholar] [Crossref]

5. Haque, ME 2013, ‘Indian Fly-Ash: Production and Consumption Scenario’, International Journal of Waste Resources, vol. 3, no. 1, pp. 22–25. [Google Scholar] [Crossref]

6. Hirajima, T, Petrus, HTBM, Oosako, Y, Nonaka, M, Sasaki, K & Ando, T 2010, ‘Recovery of cenospheres from coal fly ash using a dry separation process: Separation estimation and potential application’, International Journal of Mineral Processing, vol. 95, no. 1–4, pp. 18–24. [Google Scholar] [Crossref]

7. Ho, YS, Chiang, CC & Hsu, YC 2001, ‘Sorption kinetics for dye removal from aqueous solution using activated clay’, Separation Science and Technology, vol. 36, no. 11, pp. 2473–2488. [Google Scholar] [Crossref]

8. Ketegenov, T, Tyumentseva, O, Khan, N, Karagulanova, A & Myrzabekova, M 2019, ‘New composite fillers on the base of fly-ash cenospheres modified with titanium dioxide’, Materials Today: Proceedings, vol. 12, no. 1, pp. 128–131. [Google Scholar] [Crossref]

9. Lee, H, Deshmukh, PR, Kim, JH, Hyun, HS, Sohn, Y & Shin, WG 2019, ‘Spray drying formation of metal oxide (TiO2 or SnO2) nanoparticle coated boron particles in the form of microspheres and their physicochemical properties’, Journal of Alloys and Compounds, vol. 810, no. 40, pp. 151923. [Google Scholar] [Crossref]

10. Leng, L, Yuan, X, Zeng, G, Shao, J, Chen, X, Wu, Z, Wang, H & Peng, X 2015, ‘Surface characterization of rice husk bio-char produced by liquefaction and application for cationic dye (Malachite green) adsorption’, Fuel, vol. 155, no. 17, pp.77–85. [Google Scholar] [Crossref]

11. Li, JC, Zheng, LF, Sha, XH & Chen, P 2020, ‘Microstructural and mechanical characteristics of graphene oxide‐fly ash cenosphere hybrid reinforced epoxy resin composites’, Journal of Applied Polymer Science, vol. 137, no. 2, pp. 47173. [Google Scholar] [Crossref]

12. Lu, D, Cheng, W, Zhang, T, Lu, X, Liu, Q, Jiang, J, & Ma, J 2016, ‘Hydrophilic Fe2O3 dynamic membrane mitigating fouling of support ceramic membrane in ultrafiltration of oil/water emulsion’, Separation and Purification Technology, vol. 165, no. 9, pp. 1–9. [Google Scholar] [Crossref]

13. Novais, RM, Buruberri, LH, Seabra, MP & Labrincha, JA 2016, ‘Novel porous fly-ash containing geopolymer monoliths for lead adsorption from wastewaters’, Journal of Hazardous Materials, vol. 318, no. 18, pp. 631–640. [Google Scholar] [Crossref]

14. Sarkar, A, Rano, R, Udaybhanu, G & Basu, AK 2006, ‘A comprehensive characterisation of fly ash from a thermal power plant in Eastern India’, Fuel Processing Technology, vol. 87, no. 3, pp. 258–277. [Google Scholar] [Crossref]

15. Sharma, A, Srivastava, K, Devra, V, & Rani, A 2012, ‘Modification in Properties of Fly Ash through Mechanical and Chemical Activation’, American Chemical Science Journal, vol. 2, no. 4, pp. 177–187. [Google Scholar] [Crossref]

16. Sutcu, M, Erdogmus, E, Gencel, O, Gholampour, A, Atan, E & Ozbakkaloglu, T 2019, ‘Recycling of bottom ash and fly ash wastes in eco-friendly clay brick production’, Journal of Cleaner Production, vol. 233, no. 28, pp. 753–764. [Google Scholar] [Crossref]

17. Tang, L, Tan, XJ, Cui, FY, Zhou, Q & Yin, J 2007, ‘Reuse of carwash wastewater with hollow fiber membrane aided by enhanced coagulation and activated carbon treatments’, Water Science and Technology, vol. 56, no. 12, pp. 111–118. [Google Scholar] [Crossref]

18. Wang, D, Zhang, Y, Dong, A, Tang, Y, Wang, Y, Xia, J & Ren, N 2003, ‘Conversion of fly ash cenosphere to hollow microspheres with zeolite/mullite composite shells’, Advanced Functional Materials, vol. 13, no. 7, pp. 563–567. [Google Scholar] [Crossref]

• Machine Learning Based Surface Roughness Prediction for Parameters of ECM
• Non-Newtonian Characterization of Gelatinized Corn Starch Dispersions with Magnetic Particle Enhancement Under Shear Stress
• Performance, Evaluation and Optimization of Biodiesel from Desert Date Oil Using Response Surface Methodology
• Weld Formation Investigations of FSW of Al 6061-T6 Lapped Workpieces Using Dual Shoulders Tool
• The Relevance of Vocational Competencies in Vocational Schools (Smk) Specialising in Industrial Mechanica Engineering to the Needs of the Industry