Usability-Focused and Eco-Design for the Development of an Interior Partition Panel Made from Recycled Polylaminate.
Authors
Instituto Tecnológico de Pachuca, Pachuca de Soto, Hidalgo (Mexico)
Instituto Tecnológico de Pachuca, Pachuca de Soto, Hidalgo (Mexico)
Instituto Tecnológico de Pachuca, Pachuca de Soto, Hidalgo (Mexico)
Instituto Tecnológico de Pachuca, Pachuca de Soto, Hidalgo (Mexico)
Instituto Tecnológico de Pachuca, Pachuca de Soto, Hidalgo (Mexico)
Instituto Tecnológico de Pachuca, Pachuca de Soto, Hidalgo (Mexico)
Article Information
DOI: 10.47772/IJRISS.2026.102500025
Subject Category: Engineering & Technology
Volume/Issue: 10/25 | Page No: 420-433
Publication Timeline
Submitted: 2026-10-26
Accepted: 2026-10-31
Published: 2026-11-16
Abstract
The development of remote work and home office arrangements has increased the need to adapt interior spaces for work activities. At the same time, post-consumer multilayer packaging presents recycling challenges due to its material composition. This study aimed to develop a preliminary interior partition panel using recycled Tetra Pak packaging, applying ecodesign principles and a circular economy approach. The proposal consisted of a composite structure with two outer layers of recycled cardboard and a core made of stucco mixed with shredded post-consumer Tetra Pak. Five experimental formulations were prepared, each containing 90 g of stucco and different amounts of shredded Tetra Pak: 0, 5, 10, 15, and 20 g. The mixtures were observed during preparation and evaluated preliminarily according to their workability, cohesion, integrity, and behavior during demolding. The observations showed that increasing the amount of recycled packaging made the mixtures more fibrous and voluminous and increased their water requirements. The formulation containing 90 g of stucco and 5 g of Tetra Pak showed the most favorable relative performance during demolding, retaining greater integrity than the other formulations. However, this sample still exhibited flexibility and fragility. The formulation without Tetra Pak fractured during demolding, while the mixtures with higher packaging contents showed reduced apparent cohesion. In addition, some of the samples retained moisture during evaluation, limiting direct comparisons between formulations. These findings indicate that shredded Tetra Pak can be incorporated into a stucco matrix, but the proportions of the materials and the amount of water require further optimization. The formulation containing 5 g of Tetra Pak is therefore considered a starting point for subsequent experimentation rather than a definitive material solution.
Further controlled tests are necessary to evaluate the panel's properties before determining its suitability for interior partition applications.
Keywords
Ecodesign, circular economy, Tetra Pak waste, interior partition panel, recycled materials.
Downloads
References
1. Antwi-Afari, P., Ng, S. T., & Chen, J. (2023). Determining the optimal partition system of a modular building from a circular economy perspective: A multicriteria decision-making process. Renewable and Sustainable Energy Reviews, 185, Article 113601. https://doi.org/10.1016/j.rser.2023.113601 [Google Scholar] [Crossref]
2. Balti, S., Bouazizi, A., Boudenne, A., & Hamdi, N. (2024). Gypsum composite reinforcement with Tetra Pak-fiber-waste: Thermomechanical performance evaluation. Materials Letters, 369, Article 136735. https://doi.org/10.1016/j.matlet.2024.136735 [Google Scholar] [Crossref]
3. Bekhta, P., Lyutyy, P., Hiziroglu, S., & Ortynska, G. (2016). Properties of composite panels made from Tetra-Pak and polyethylene waste material. Journal of Polymers and the Environment, 24(2), 159–165. https://doi.org/10.1007/s10924-016-0758-7 [Google Scholar] [Crossref]
4. Bonocore, G., & De Luca, P. (2022). Preparation and characterization of insulating panels from recycled polylaminate (Tetra Pak) materials. Sustainability, 14(11), Article 6858. https://doi.org/10.3390/su14116858 [Google Scholar] [Crossref]
5. Braun, V., & Clarke, V. (2006). Using thematic analysis in psychology. Qualitative Research in Psychology, 3(2), 77–101. https://doi.org/10.1191/1478088706qp063oa [Google Scholar] [Crossref]
6. Cerna Alvárez, D. (2024). Factores de riesgo psicosocial en el teletrabajo: El caso de México [Psychosocial risk factors in teleworking: The case of Mexico]. Contextualizaciones Latinoamericanas(31), 23–34. https://doi.org/10.32870/cl.v2i31.8056 [Google Scholar] [Crossref]
7. Creswell, J. W., & Creswell, J. D. (2018). Research design: Qualitative, quantitative, and mixed methods approaches (5th ed.). SAGE Publications. [Google Scholar] [Crossref]
8. Davis, F. D. (1989). Perceived usefulness, perceived ease of use, and user acceptance of information technology. MIS Quarterly, 13(3), 319–340. https://doi.org/10.2307/249008 [Google Scholar] [Crossref]
9. Defranc Balanzategui, P. O., & Arellano Valdiviezo, A. I. (2024). Consideraciones sobre ergonomía física y cognitiva en el ámbito laboral [Considerations on physical and cognitive ergonomics in the workplace]. Más Vita, 6(3), 106–118. https://doi.org/10.47606/ACVEN/MV0244 [Google Scholar] [Crossref]
10. Ferrández, D., Zaragoza-Benzal, A., Santos, P., & Durães, L. (2023). Characterisation of new sustainable gypsum composites with low-density polyethylene waste from single-use bags. Journal of Building Engineering, 80, Article 108103. https://doi.org/10.1016/j.jobe.2023.108103 [Google Scholar] [Crossref]
11. Foti, D., Adamopoulos, S., Voulgaridou, E., Voulgaridis, E., Passialis, C., Amiandamhen, S. O., & Daniel, G. (2019). Microstructure and compressive strength of gypsum-bonded composites with papers, paperboards and Tetra Pak recycled materials. Journal of Wood Science. https://doi.org/10.1186/s10086-019-1821-5 [Google Scholar] [Crossref]
Metrics
Views & Downloads
Similar Articles
- The Impact Of UI/UX Design on User Trust and Task Completion in Civic Tech Platforms
- Solar Cell Photovoltaic Model Shell Sp 75
- Development of an Intelligent Traffic Management System to Address Visibility Obstruction at Urban Intersections: A Case Study of Ibadan Metropolis
- Optimum Placement of Facts Devices on an Interconnected Power Systems Using Particle Swarm Optimisation Technique
- Assessing Construction Transformation and Implication on Future Production Flow System