Reducing Manufacturing Waste in the Copper Industry through Lean Six Sigma and Value Stream Mapping: An Industrial Case Study in Malaysia
Authors
Muhammad Khairul Rezwan Abdul Rahman
Faculty of Mechanical Engineering, Universiti Teknologi MARA, Shah Alam, Selangor (Malaysia)
Faculty of Mechanical Engineering, Universiti Teknologi MARA, Shah Alam, Selangor (Malaysia)
Quality Department, Metrod (M) Sdn. Bhd (Malaysia)
Article Information
DOI: 10.47772/IJRISS.2026.101000749
Subject Category: Engineering & Technology
Volume/Issue: 10/10 | Page No: 10524-10548
Publication Timeline
Submitted: 2026-10-25
Accepted: 2026-10-30
Published: 2026-11-17
Abstract
Continuous copper rod manufacturing is highly sensitive to upstream process instability, yet Lean Six Sigma research has rarely examined continuous metallurgical processes. This study evaluates the effectiveness of Value Stream Mapping (VSM) in reducing waste and enhancing operational performance in the upstream Continuous Casting and Rolling (CCR) process of a Malaysian copper manufacturer. An industrial case study was conducted using VSM as the primary analytical tool, supported by the Define, Measure, Analyse, Improve and Control (DMAIC) framework. SAP production records, including coil-by-coil rod reports, were cross-validated against SCADA data and shop-floor observations to map the current state, quantify value-added time, prioritise defects using Pareto and Ishikawa analyses, and evaluate Overall Equipment Effectiveness (OEE). Five targeted Kaizen interventions were implemented across the Loader, Melting Furnace, Casting Wheel, Rolling Mill and Coiler workstations. A comparison between the baseline (Week 10, 718 coils) and post-improvement (Week 41, 673 coils) periods revealed a statistically significant 17% relative reduction in the copper rod downgrade rate (31.34% to 26.00%; p = 0.028), alongside an increase in OEE from 63.49% to 67.58%, primarily driven by improved quality performance. The Future State VSM projected a 40% reduction in production process lead time, from 32.02 to 19.21 hours. Chemical-impurity downgrades decreased from 16.7% to 3.0% following material verification at the Loader, while pallet-related defects were eliminated at the Coiler. However, oxygen-, surface- and peeling-related defects increased. Based on copper prices and exchange rates matched to the respective assessment dates, the estimated 139.9 tonnes of weekly downgrades avoided represent an economic benefit of RM 0.15–0.30 million, after accounting for market price fluctuations. Given the single-site design, longer-term performance monitoring and multi-site validation are recommended.
Keywords
Value stream mapping, Lean Six Sigma, DMAIC, copper rod manufacturing, waste reduction
Downloads
References
1. Abdelwahed, M. S., Alghamdi, A., & Eltaher, M. A. (2024). Improving product quality of wire drawing process using design of experiments. Journal of Computational Applied Mechanics, 55(1), 8–25. https://doi.org/10.22059/JCAMECH.2024.372017.957 [Google Scholar] [Crossref]
2. Alexandrov, S., Hwang, Y.-M., & Tsui, H. S. R. (2022). Determining the drawing force in a wire drawing process considering an arbitrary hardening law. Processes, 10(7), Article 1336. https://doi.org/10.3390/pr10071336 [Google Scholar] [Crossref]
3. ASTM International. (1995). Standard specification for soft or annealed copper wire (ASTM B3-95). [Google Scholar] [Crossref]
4. ASTM International. (2010). Standard specification for electrolytic copper cathode (ASTM B115-10). [Google Scholar] [Crossref]
5. ASTM International. (2017). Standard specification for copper rod for electrical purposes (ASTM B49-17). [Google Scholar] [Crossref]
6. Batwara, A., Sharma, V., Makkar, M., & Giallanza, A. (2023). Towards smart sustainable development through value stream mapping – A systematic literature review. Heliyon, 9(5), Article e15852. https://doi.org/10.1016/j.heliyon.2023.e15852 [Google Scholar] [Crossref]
7. Chaudhari, S., & Nemade, G. (2024). Optimizing manufacturing operations: A comprehensive study of SAP ERP with an emphasis on SAP MM. International Journal of Engineering Research & Technology, 13(9), Article IJERTV13IS090019. https://www.ijert.org/optimizing-manufacturing-operations-a-comprehensive-study-of-sap-erp-with-an-emphasis-on-sap-mm [Google Scholar] [Crossref]
8. Chia, E. H., & Adams, R. D. (1981). The metallurgy of Southwire’s continuous rod. JOM, 33(2), 68–74. https://doi.org/10.1007/BF03354529 [Google Scholar] [Crossref]
9. González, Á., Cruchaga, M., Celentano, D., & Ponthot, J.-P. (2024). Damage prediction in the wire drawing process. Metals, 14(10), Article 1174. https://doi.org/10.3390/met14101174 [Google Scholar] [Crossref]
10. Haddi, A., Imad, A., & Vega, G. (2011). Analysis of temperature and speed effects on the drawing stress for improving the wire drawing process. Materials & Design, 32(8–9), 4310–4315. https://doi.org/10.1016/j.matdes.2011.04.010 [Google Scholar] [Crossref]
11. Jones, T. D. A., Strachan, R. I., Mackie, D. M., Cooper, M., Frame, B., & Vorstius, J. B. (2021). Computational fluid dynamic simulations of solidification for enhancing speed of continuous cast copper. Engineering Science and Technology, an International Journal, 24(1), 92–104. https://doi.org/10.1016/j.jestch.2020.12.009 [Google Scholar] [Crossref]
12. Larsson, J., Jansson, A., & Karlsson, P. (2019). Monitoring and evaluation of the wire drawing process using thermal imaging. The International Journal of Advanced Manufacturing Technology, 101, 2121–2134. https://doi.org/10.1007/s00170-018-3021-7 [Google Scholar] [Crossref]
13. Liu, Y., Peng, Y., & Qu, X. (2021). Mechanism of and key technologies for copper bonding in the hot rolling of SCR continuous casting and rolling. Applied Sciences, 11(22), Article 11023. https://doi.org/10.3390/app112211023 [Google Scholar] [Crossref]
14. Mittal, A., Gupta, P., Kumar, V., Al Owad, A., Mahlawat, S., & Singh, S. (2023). The performance improvement analysis using Six Sigma DMAIC methodology: A case study on Indian manufacturing company. Heliyon, 9(3), Article e14625. https://doi.org/10.1016/j.heliyon.2023.e14625 [Google Scholar] [Crossref]
15. Nurhidayah, F. A., Chumaidiyah, E., & Suhendra, A. A. (2025). Design of ERP production planning module to optimize the use of System Application and Processing (SAP) software using business process improvement and Activate SAP methodology at PT. XYZ. International Journal of Inventive Engineering and Sciences, 12(1), 15–19. https://doi.org/10.35940/ijies.H1094.12010125 [Google Scholar] [Crossref]
16. Odeyinka, O. F., Ipinnimo, O., & Ogunwolu, F. (2024). Parametric multi-level modeling of Lean Six Sigma. Journal of Engineering and Applied Science, 71, Article 193. https://doi.org/10.1186/s44147-024-00528-1 [Google Scholar] [Crossref]
17. Rother, M., & Shook, J. (1999). Learning to see: Value stream mapping to add value and eliminate muda. Lean Enterprise Institute. [Google Scholar] [Crossref]
18. Sachin, S., & Dileeplal, J. (2017). Six Sigma methodology for improving manufacturing process in a foundry industry. International Journal of Advanced Engineering Research and Science, 4(5), 131–136. https://doi.org/10.22161/ijaers.4.5.21 [Google Scholar] [Crossref]
19. Salwin, M., Jacyna-Gołda, I., Bańka, M., Varanchuk, D., & Gavina, A. (2021). Using value stream mapping to eliminate waste: A case study of a steel pipe manufacturer. Energies, 14(12), Article 3527. https://doi.org/10.3390/en14123527 [Google Scholar] [Crossref]
20. Salwin, M., Pszczółkowska, K., Pałęga, M., & Kraslawski, A. (2023). Value-stream mapping as a tool to improve production and energy consumption: A case study of a manufacturer of industrial hand tools. Energies, 16(21), Article 7292. https://doi.org/10.3390/en16217292 [Google Scholar] [Crossref]
21. Setiawan, S. A. (2025). Implementation of Six Sigma methodology to reduce high defect rate in rubber processing industry. European Journal of Business and Management Research, 10(1), 118–126. https://doi.org/10.24018/ejbmr.2025.10.1.2538 [Google Scholar] [Crossref]
22. Sinha, U., & Adams, R. (1993). Southwire Continuous Rod process: Innovations for quality improvements. Wire Journal International, 26(6), 66. [Google Scholar] [Crossref]
23. ValutaFX. (2025a). US dollar (USD) to Malaysian ringgit (MYR) exchange rate on 2025-03-05. Retrieved November 3, 2026, from https://www.valutafx.com/history/usd-myr-2025-03-05 [Google Scholar] [Crossref]
24. ValutaFX. (2025b). US dollar (USD) to Malaysian ringgit (MYR) exchange rate on 2025-10-08. Retrieved November 3, 2026, from https://www.valutafx.com/history/usd-myr-2025-10-08 [Google Scholar] [Crossref]
25. Ware, P. W. (2007). The SCR® process produces high quality copper rod around the world. Canadian Institute of Mining, Metallurgy and Petroleum. https://onemine.org/documents/the-scr-process-produces-high-quality-copper-rod-around-the-world [Google Scholar] [Crossref]
26. Westmetall. (2025). LME copper cash-settlement prices, 2025 [Data set]. Retrieved November 3, 2026, from https://www.westmetall.com/en/markdaten.php?action=table&field=LME_Cu_cash&year=2025 [Google Scholar] [Crossref]
Metrics
Views & Downloads
Similar Articles
- The Impact Of UI/UX Design on User Trust and Task Completion in Civic Tech Platforms
- Solar Cell Photovoltaic Model Shell Sp 75
- Development of an Intelligent Traffic Management System to Address Visibility Obstruction at Urban Intersections: A Case Study of Ibadan Metropolis
- Optimum Placement of Facts Devices on an Interconnected Power Systems Using Particle Swarm Optimisation Technique
- Assessing Construction Transformation and Implication on Future Production Flow System