Multi-Wavelength Analysis of Intensity-Modulated U-Shaped Plastic Optical Fiber Humidity Sensors

This paper presents a comprehensive multi-wavelength characterization of a humidity sensor based on an intensity-modulated U-shaped tapered plastic optical fiber (POF). The sensor exploits evanescent-wave interaction between guided light and the surrounding environment, enabling variations in relative humidity (RH) to modulate the transmitted optical power. A Mitsubishi SH4001 POF was manually tapered using fine-grade abrasive polishing to produce waist diameters of 500 µm and 600 µm, followed by bending into U-shaped structures with radii of 3 cm, 4 cm, and 5 cm. Light from light-emitting diodes (LEDs) at 470 nm, 530 nm, and 645 nm was launched into the fiber, and changes in output intensity were measured using a phototransistor and microcontroller-based signal acquisition system. Experimental results, obtained over 35–90 %RH, reveal a consistent inverse relationship between humidity and output voltage for all wavelengths. Among all configurations, the 645 nm wavelength paired with a 500 µm waist and 5 cm bend radius yielded the highest sensitivity of 0.0385 V/%RH and linearity of 98.74%. Comparative analysis demonstrates the significant influence of wavelength on evanescent-wave penetration depth and sensing performance. The findings confirm the suitability of tapered POF sensors as low-cost and robust alternatives for environmental humidity monitoring.

humidity sensor; evanescent wave; multi-wavelength; intensity modulation; U-shaped fiber

1. J. Zubia and J. Arrue, “Plastic Optical Fibers: An Introduction to Their Technological Processes and Applications,” Optical Fiber Technology, 2001. [Google Scholar] [Crossref]

2. R. Bilro, L. Alberto, and R. Nogueira, “POF Sensors: A Review,” Sensors, vol. 12, pp. 1215–1238, 2012. [Google Scholar] [Crossref]

3. J. Ascorbe, J. M. Corres, F. J. Arregui, and I. R. Matías, “Recent Developments in Fiber Optic Humidity Sensors,” Sensors, vol. 17, no. 4, 2017. [Google Scholar] [Crossref]

4. J. J. Patil and A. Ghosh, “Intensity Modulation-Based U-Shaped Plastic Optical Fiber Refractive Index Sensor,” Sensors and Actuators B: Chemical, vol. 219, pp. 204–211, 2015. [Google Scholar] [Crossref]

5. A. Leal-Junior et al., “Behaviour of U-Shaped Polymer Optical Fibre Sensors,” Measurement, vol. 118, pp. 113–122, 2018. [Google Scholar] [Crossref]

6. D. K. Kim and Y. Chung, “Tapered Optical Fibre Sensors: A Review,” Optical Fiber Technology, vol. 20, no. 6, pp. 608–619, 2014. [Google Scholar] [Crossref]

7. Mitsubishi Rayon Co., “POF Material Characteristics and Attenuation Profiles,” Technical Documentation, 2010. [Google Scholar] [Crossref]

8. Z. Zhong et al., “Plastic Optical Fiber Sensor for Temperature-Independent High-Sensitivity Detection of Humidity,” Applied Optics, vol. 59, no. 18, pp. 5708–5713, 2020. [Google Scholar] [Crossref]

9. X. Cheng, “High-Resolution Polymer Optical Fiber Humidity Sensor,” Measurement Science and Technology, vol. 32, no. 11, 2021. [Google Scholar] [Crossref]

10. S. Hussian et al., “Development of a Dual Point Humidity Sensor Using POF Based on Twisted Fiber Structure,” Scientific Reports, vol. 14, Article 10735, 2024. [Google Scholar] [Crossref]

11. H. Dang et al., “Compact Fabry–Pérot Interferometric Fiber Optic Humidity Sensors Using Polymer Materials,” Polymers, vol. 17, no. 21, 2810, 2025. [Google Scholar] [Crossref]

12. A. Pospori et al., “Temperature and Humidity Sensitivity of Polymer Optical Fibre Sensors Tuned by Pre-Strain,” Sensors, vol. 22, no. 6, 2022. [Google Scholar] [Crossref]

13. J. Qian et al., “Humidity Sensing Using Polymers: A Critical Review of Current Technologies and Emerging Trends,” Chemosensors, vol. 12, no. 11, 230, 2024. [Google Scholar] [Crossref]

14. X. Lu, K. Hicke, M. Breithaupt, and C. Strangfeld, “Distributed Humidity Sensing in Concrete Based on Polymer Optical Fiber,” Polymers, 2021. [Google Scholar] [Crossref]

15. H. Kuswanto, I. Abimanyu, and W. Dwandaru, “Increasing the Sensitivity of Polymer Optical Fiber Sensing Element in Detecting Humidity: Combination of Macro and Micro Bendings,” Trends in Sciences, 2022. [Google Scholar] [Crossref]

16. S. Johari, T. Z. Cheak, H. R. A. Rahim, M. Jali, H. H. M. Yusof, M. A. M. Johari, M. Yasin, and S. Harun, “ZnO Nanorods Coated Tapered U-Shape Plastic Optical Fiber for Relative Humidity Detection,” Photonics, 2022. [Google Scholar] [Crossref]

17. E. Afsharipour, K. D. Malviya, M. Montazeri, E. Mortazy, R. Soltanzadeh, A. Hassani, F. Rosei, and M. Chaker, “Evanescent-Field Excited Surface Plasmon-Enhanced U-Bent Fiber Probes Coated with Au and ZnO Nanoparticles for Humidity Detection,” Processes, 2023. [Google Scholar] [Crossref]

18. Y. Liang and J. Wang, “Non-Adiabatically Tapered Optical Fiber Humidity Sensor with High Sensitivity and Temperature Compensation,” Sensors (Basel, Switzerland), 2025. [Google Scholar] [Crossref]

• The Impact Of UI/UX Design on User Trust and Task Completion in Civic Tech Platforms
• Solar Cell Photovoltaic Model Shell Sp 75
• Development of an Intelligent Traffic Management System to Address Visibility Obstruction at Urban Intersections: A Case Study of Ibadan Metropolis
• Optimum Placement of Facts Devices on an Interconnected Power Systems Using Particle Swarm Optimisation Technique
• Assessing Construction Transformation and Implication on Future Production Flow System