Design, Thermal Performance, and Environmental Safety Analysis of a 304 Stainless Steel Al-Quran Disposal Incinerator for State Religious Authorities

Authors

Hasib, H.

Faculty of Industrial and Manufacturing Technology and Engineering, Universiti Teknikal Malaysia Melaka (UTeM), Melaka, Malaysia (Malaysia)

Hamid, R.A.

Faculty of Industrial and Manufacturing Technology and Engineering, Universiti Teknikal Malaysia Melaka (UTeM), Melaka, Malaysia (Malaysia)

Yahaya, S.H.

Faculty of Industrial and Manufacturing Technology and Engineering, Universiti Teknikal Malaysia Melaka (UTeM), Melaka, Malaysia (Malaysia)

Article Information

DOI: 10.47772/IJRISS.2026.101000694

Subject Category: Engineering

Volume/Issue: 10/10 | Page No: 9688-9695

Publication Timeline

Submitted: 2026-10-25

Accepted: 2026-10-30

Published: 2026-11-16

Abstract

The respectful disposal of damaged Quranic texts presents a crucial socio-religious and environmental management issue for Islamic religious authorities. In Malaysia, the DepartmenThe respectful disposal of damaged Quranic texts presents a crucial socio-religious and environmental management issue for Islamic religious authorities. In Malaysia, the Department of Islamic Development Malaysia (JAKIM) guidelines specify controlled burning as an approved method. However, existing disposal incinerators operated by state authorities, such as Jabatan Agama Islam Melaka (JAIM), face significant operational issues, including excessive toxic smoke emissions, ergonomic limitations, ash loss due to wind scattering, and performance degradation from 300 kg/day to 150 kg/day after two years. This study presents the design, Finite Element Analysis (FEA), and Computational Fluid Dynamics (CFD) simulation of a redesigned 304 stainless steel Al-Quran disposal incinerator. Concept selection using the Pugh Matrix identified an optimized design incorporating an air blower, smoke filter, dust compartment, and hydraulic lift table. CFD simulations demonstrate that forced aeration elevates internal combustion temperature from 617 °C (blower off) to 1,725 °C (blower on), increasing thermal efficiency and reducing total burning time for 150 kg of paper to under 24 hours. Static FEA using the Von Mises Yield Criterion indicates that while the structure safely supports 300 kg under ambient conditions (FOS = 1.0), thermal stresses at 1,725 °C limit the safe structural payload to 150 kg (FOS = 1.1). To mitigate high-temperature sensitization (425–870 °C) and intergranular corrosion, protective enamel or Ni-Cr composite coatings are evaluated. This integrated engineering solution successfully harmonizes religious sanctity, environmental safety, and operational sustainability for public religious governancet of Islamic Development Malaysia (JAKIM) guidelines specify controlled burning as an approved method. However, existing disposal incinerators operated by state authorities, such as Jabatan Agama Islam Melaka (JAIM), face significant operational issues, including excessive toxic smoke emissions, ergonomic limitations, ash loss due to wind scattering, and performance degradation from 300 kg/day to 150 kg/day after two years. This study presents the design, Finite Element Analysis (FEA), and Computational Fluid Dynamics (CFD) simulation of a redesigned 304 stainless steel Al-Quran disposal incinerator. Concept selection using the Pugh Matrix identified an optimized design incorporating an air blower, smoke filter, dust compartment, and hydraulic lift table. CFD simulations demonstrate that forced aeration elevates internal combustion temperature from 617 °C (blower off) to 1,725 °C (blower on), increasing thermal efficiency and reducing total burning time for 150 kg of paper to under 24 hours. Static FEA using the Von Mises Yield Criterion indicates that while the structure safely supports 300 kg under ambient conditions (FOS = 1.0), thermal stresses at 1,725 °C limit the safe structural payload to 150 kg (FOS = 1.1). To mitigate high-temperature sensitization (425–870 °C) and intergranular corrosion, protective enamel or Ni-Cr composite coatings are evaluated. This integrated engineering solution successfully harmonizes religious sanctity, environmental safety, and operational sustainability for public religious governance.

Keywords

Al-Quran disposal, 304 stainless steel, incinerator design, Computational Fluid Dynamics (CFD), Finite Element Analysis (FEA), public environmental safety, Islamic governance

Downloads

References

1. Hassan, R., Azmi, H., Islah Bakri, I. M., & Abd Wahab, M. N. (2015). Design and development of used Al-Quran paper disposal system. Jurnal Teknologi, 76(6), 125–130. [Google Scholar] [Crossref]

2. https://doi.org/10.11113/jt.v76.5669 [Google Scholar] [Crossref]

3. Huda. (2022). Respectful and proper disposal of the Quran. Learn Religions. [Google Scholar] [Crossref]

4. https://www.learnreligions.com/disposal-of-quran-2004546 [Google Scholar] [Crossref]

5. Verma, R., Vinoda, K. S., Papireddy, M., & Gowda, A. N. S. (2016). Toxic pollutants from plastic waste: A review. Procedia Environmental Sciences, 35, 701–708. [Google Scholar] [Crossref]

6. https://doi.org/10.1016/J.PROENV.2016.07.069 [Google Scholar] [Crossref]

7. Hu, H. H. (2012). Computational fluid dynamics. Fluid Mechanics, Academic Press, 421–472. [Google Scholar] [Crossref]

8. https://doi.org/10.1016/B978-0-12-382100-3.10010-1 [Google Scholar] [Crossref]

9. Limpinsel, M., Kuo, D., & Vijh, A. (2018). SMARTS modeling of solar spectra at stratospheric altitude. 2018 IEEE 7th World Conference on Photovoltaic Energy Conversion (WCPEC), 3367–3373. [Google Scholar] [Crossref]

10. https://doi.org/10.1109/PVSC.2018.8547665 [Google Scholar] [Crossref]

11. Mills, D. (2016). Airflow rate evaluation. Pneumatic Conveying Design Guide, Butterworth-Heinemann, 199–225. https://doi.org/10.1016/B978-0-08-100649-8.00009-3 [Google Scholar] [Crossref]

12. Pratama, J., & Mahardika, M. (2018). Finite element analysis to determine the stress distribution, displacement and safety factor on a microplate for fractured jaw. AIP Conference Proceedings, 1941(1), 020022. https://doi.org/10.1063/1.5028080 [Google Scholar] [Crossref]

13. Adu, R. O., Gyasi, S. F., Essumang, D. K., & Adu-Gyamfi, S. (2022). Design and construction of a gas filter system for hospital incinerators. Environmental Challenges, 9, 100651. [Google Scholar] [Crossref]

14. https://doi.org/10.1016/J.ENVC.2022.100651 [Google Scholar] [Crossref]

15. Purohit, R., Khitoliya, P., & Koli, D. K. (2014). Design and finite element analysis of an automotive clutch assembly. Procedia Materials Science, 6, 490–502. https://doi.org/10.1016/j.mspro.2014.07.063 [Google Scholar] [Crossref]

16. Jin, B. Z., Deng, Y. F., Li, G. X., & Li, H. M. (2022). Experimental and numerical study of the laminar burning velocity of NH3/H2/air premixed flames at elevated pressure and temperature. International Journal of Hydrogen Energy, 47(85), 36046–36057. https://doi.org/10.1016/J.IJHYDENE.2022.08.198 [Google Scholar] [Crossref]

17. Babakr, A., Al-Meshari, A. A., & Thomas, S. (2004). Caustic stress corrosion cracking of 304 SS incinerator material. Corrosion/2004, Paper No. 04521. [Google Scholar] [Crossref]

18. Li, H., Liu, H., Bai, M., Zhang, X., Chi, H., Chen, T., Yu, Y., & Yao, H. (2023). Insight into the corrosion resistance of Mo-added NiCrBSi coating in simulated waste incineration environment. Corrosion Science, 216, 111085. https://doi.org/10.1016/j.corsci.2023.111085 [Google Scholar] [Crossref]

19. Zhang, H., Yang, L., Zhang, X., Wang, Q., Wu, J., Liu, Z., Zeng, C., & Zhu, S. (2023). Effect of enamel coating on the hot corrosion of 304 stainless steel beneath KCl–ZnCl2 deposits at 450 °C. Journal of Materials Research and Technology, 23, 245–257. [Google Scholar] [Crossref]

20. https://doi.org/10.1016/j.jmrt.2022.12.152 [Google Scholar] [Crossref]

21. Mudgal, D., Singh, S., & Prakash, S. (2014). Corrosion problems in incinerators and biomass-fuel-fired boilers. International Journal of Corrosion, 2014, 505306. https://doi.org/10.1155/2014/505306 [Google Scholar] [Crossref]

22. Ahuja, L., & Mudgal, D. (2020). High temperature corrosion performance of ceria doped Cr3C2-NiCr coated superalloys under actual medical waste atmosphere. Materials Today: Proceedings, 28(2), 599–603. https://doi.org/10.1016/j.matpr.2019.12.228 [Google Scholar] [Crossref]

Metrics

Views & Downloads

Similar Articles