Increasing Productivity in Hidalgo through Additive Manufacturing: A Case Study in SMEs

Authors

Keyla Espinosa Ramos

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Enrique de Jesús Mohedano Torres

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Guillermo Acosta Mendoza

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Gabriela Calva Arcega

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Adrián Sánchez Ortega

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Alejandra Lugo Islas

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Article Information

DOI: 10.47772/IJRISS.2026.102500004

Subject Category: Education

Volume/Issue: 10/25 | Page No: 44-56

Publication Timeline

Submitted: 2026-10-14

Accepted: 2026-10-19

Published: 2026-11-14

Abstract

Micro, small, and medium-sized enterprises (SMEs) form the backbone of regional economies such as Hidalgo, Mexico, yet they frequently exhibit productivity lags relative to larger firms due to limited technology adoption, inefficient traditional processes, and high material waste. Additive manufacturing (AM), particularly low-cost fused deposition modeling (FDM), offers a promising pathway to address these constraints by enabling on-demand production, reduced waste, and shorter cycle times without large capital investments. This study evaluates the impact of implementing accessible AM technologies on productivity metrics in a representative manufacturing SME in Hidalgo and proposes a replicable six-phase implementation methodology.
A mixed-methods experimental case study was employed. A PRISMA systematic review of 20 articles (2016–2026) informed the intervention design and variable selection. The empirical component consisted of a longitudinal single-case study with four phases: baseline diagnosis, process redesign, a six-month pilot, and evaluation. Quantitative pre-post comparisons of cycle time, waste rate, monthly production, operational efficiency, and overall productivity were triangulated with qualitative data from surveys and interviews.
The pilot, based on open-source FDM printers and software, produced substantial improvements. Cycle time decreased from 45 to 27 minutes per unit (40% reduction), material waste declined by approximately 40%, monthly production rose from 150 to 200 units (33% increase), operational efficiency improved from 60% to 90%, and overall productivity increased by 35%. These gains were achieved with moderate investment and targeted training of 15–25% of production staff. The findings support the hypothesis and align with literature benchmarks for low-volume AM applications while addressing the scarcity of experimental pre-post evidence in regional Mexican SMEs.
The proposed six-phase methodology provides a practical, low-risk pathway for other resource-constrained SMEs. Limitations of the single-case design are acknowledged, and future research directions include multi-firm implementations and longer-term sustainability assessment

Keywords

additive manufacturing, productivity, SMEs, optimization, Hidalgo, PRISMA

Downloads

References

1. Arcos-Novillo, D. A., y Güemes-Castorena, D. (2017). Development of an additive manufacturing technology scenario for opportunity identification—The case of Mexico. Futures, 90, 1–15. https://doi.org/10.1016/j.futures.2017.05.001 [Google Scholar] [Crossref]

2. Bettiol, M., Capestro, M., Di Maria, E., y Micelli, S. (2021). SMEs @ Industry 4.0: A comparison between top and average performers. Sinergie Italian Journal of Management, 39(2), 27–44. https://doi.org/10.7433/s116.2021.03 [Google Scholar] [Crossref]

3. Cirillo, V., Fanti, L., Mina, A., y Ricci, A. (2023). The adoption of digital technologies: Investment, skills, work organisation. Structural Change and Economic Dynamics, 66, 89–105. https://doi.org/10.1016/j.strueco.2023.04.006 [Google Scholar] [Crossref]

4. Diractum. (2025). Productividad e impresión 3D en México. [Reporte empresarial]. [Google Scholar] [Crossref]

5. Frazier, W. E., Lu, Y., y Witherell, P. (2024). Empowering small and medium-sized enterprises through effective additive manufacturing data management (NIST AMS 100-59). National Institute of Standards and Technology. https://doi.org/10.6028/NIST.AMS.100-59 [Google Scholar] [Crossref]

6. Gibson, I., Rosen, D., Stucker, B., y Khorasani, M. (2021). Additive manufacturing technologies (3rd ed.). Springer. https://doi.org/10.1007/978-3-030-56127-7 [Google Scholar] [Crossref]

7. Haug, A., Wickstrøm, K. A., Stentoft, J., y Philipsen, K. (2023). Adoption of additive manufacturing: A survey of the role of knowledge networks and maturity in small and medium-sized Danish production firms. International Journal of Production Economics, 255, 108714. https://doi.org/10.1016/j.ijpe.2022.108714 [Google Scholar] [Crossref]

8. INEGI. (2024). Estadísticas de productividad y digitalización en Mypes manufactureras mexicanas. Instituto Nacional de Estadística y Geografía. [Google Scholar] [Crossref]

9. Liberati, A., Altman, D. G., Tetzlaff, J., Mulrow, C., Gøtzsche, P. C., Ioannidis, J. P. A., Clarke, M., Devereaux, P. J., Kleijnen, J., y Moher, D. (2009). The PRISMA statement for reporting systematic reviews and meta-analyses of studies that evaluate health care interventions: Explanation and elaboration. PLoS Medicine, 6(7), e1000100. https://doi.org/10.1371/journal.pmed.1000100 [Google Scholar] [Crossref]

10. López, O. E. (2025). Impresión 3D industrial y nearshoring en México. Modern Machine Shop México. [Google Scholar] [Crossref]

11. Marzi, G., Zollo, L., Boccardi, A., y Ciappei, C. (2018). Additive manufacturing in SMEs: Empirical evidences from Italy. International Journal of Innovation and Technology Management, 15(1), 1850007. https://doi.org/10.1142/S0219877018500074 [Google Scholar] [Crossref]

12. McConnell, S., Tanner, D., y Kourousis, K. I. (2024). Productivity improvement opportunities for metal powder bed fusion technologies: A systematic literature review. Rapid Prototyping Journal, 30(11), 231–246. https://doi.org/10.1108/RPJ-09-2023-0333 [Google Scholar] [Crossref]

13. OECD. (2019). OECD Territorial Reviews: Hidalgo, Mexico. OECD Publishing. https://doi.org/10.1787/9789264310391-en [Google Scholar] [Crossref]

14. Page, M. J., McKenzie, J. E., Bossuyt, P. M., Boutron, I., Hoffmann, T. C., Mulrow, C. D., Shamseer, L., Tetzlaff, J. M., Akl, E. A., Brennan, S. E., Chou, R., Glanville, J., Grimshaw, J. M., Hróbjartsson, A., Lalu, M. M., Li, T., Loder, E. W., Mayo-Wilson, E., McDonald, S., ... Moher, D. (2021). The PRISMA 2020 statement: An updated guideline for reporting systematic reviews. BMJ, 372, n71. https://doi.org/10.1136/bmj.n71 [Google Scholar] [Crossref]

15. Rodríguez Salvador, M., Hernández de Menéndez, A. M., y Arcos Novillo, D. A. (2016). Additive manufacturing: Importance and challenges for Latin America. En Anticipating Future Innovation Pathways Through Large Data Analysis (pp. 249–271). Springer. https://doi.org/10.1007/978-3-319-39056-7_14 [Google Scholar] [Crossref]

16. Rogers, E. M. (2003). Diffusion of innovations (5th ed.). Free Press. [Google Scholar] [Crossref]

17. Sáenz, R. (2025). 3D printing and design: A new era for Mexico’s industry. Mexico Business News. https://mexicobusiness.news/aerospace/news/3d-printing-and-design-new-era-mexicos-industry [Google Scholar] [Crossref]

18. Saldana-Robles, A. L., Balvantin-Garcia, A. J., Aguilera-Gomez, E., et al. (2019). The insertion of low-cost additive manufacturing into engineering teaching: A case in central Mexico. International Journal of Materials and Product Technology, 59(3), 270–285. https://doi.org/10.1504/IJMPT.2019.102944 [Google Scholar] [Crossref]

19. Sæterbø, M., y Solvang, W. D. (2024). Metal additive manufacturing adoption in SMEs: Technical attributes, challenges, and opportunities. Journal of Manufacturing Processes, 128, 175–189. https://doi.org/10.1016/j.jmapro.2024.07.074 [Google Scholar] [Crossref]

20. Suarez-Luna, J. M., Romero-Guerrero, J. A., y Arenas-Islas, D. (2024). Productividad de granjas de manufactura aditiva en la cadena de suministro industrial. Pädi Boletín Científico de Ciencias Básicas e Ingenierías del ICBI, 12(Especial 4), 236–242. https://doi.org/10.29057/icbi.v12iespecial4.13268 [Google Scholar] [Crossref]

21. Vázquez Rojas, A. M., Rodríguez Juárez, E., y González Gómez, D. X. (2016). Un análisis de la productividad manufacturera en el Estado de Hidalgo. Cimexus, 11(2), 13–28. [Google Scholar] [Crossref]

Metrics

Views & Downloads

Similar Articles