Prioritization of Machinery Replacement through Incremental Economic Analysis and FUCOM-TOPSIS in a Furniture Company in Hidalgo

Authors

Dariana Anaya González

Secretaría de Planeación, Fianzas y Administración (Mexico)

Verónica Gómez Arriaga

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Yohensis Mariam Guillen Zamora

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Claudia Reyes Bolaños

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Carlos Darío Acevedo Magaña

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Erik Rodríguez Soto

Instituto Tecnológico de Pachuca, Hidalgo (Mexico)

Article Information

DOI: 10.47772/IJRISS.2026.102500003

Subject Category: Education

Volume/Issue: 10/25 | Page No: 27-43

Publication Timeline

Submitted: 2026-10-14

Accepted: 2026-10-19

Published: 2026-11-14

Abstract

The renewal of machinery in companies with limited financial resources requires distinguishing between the economic convenience of replacing an asset and the relative priority of the available projects. This study analyzes four proposed replacements for Mobilesco con Firmeza, a furniture company located in Hidalgo, Mexico: panel saw, industrial cutoff saw, electrostatic paint booth, and electrostatic paint oven. A quantitative, non-experimental, documentary case study was developed, based on the critical review of the provided file. The procedure reconstructed the defender–challenger cash flows, calculated present value, annual worth, and incremental internal rate of return, and used the weights attributed to FUCOM to perform a TOPSIS ranking. Inconsistencies of transcription, economic thresholds, and sensitivity scenarios were also examined. The corrected results ranked the panel saw in first place, with a closeness coefficient of 0.814232, followed by the cutoff saw, the oven, and the booth. However, the four projects presented negative incremental present values at the recorded evaluation rates. The panel saw would require additional net benefits of 8,072.21 pesos per year to reach financial equilibrium. Its first position was preserved in 21 of 22 individual weight perturbations, but passed to the cutoff saw when the relative weight of capacity was increased by 20%. The hypothesis of priority for the panel saw received conditional support; that of immediate economic viability was not supported. It is concluded that the model allows organizing the review of investments, although it does not by itself justify their execution. Its definitive application requires validating the technical valuations, homologating energy consumption, and documenting the original preferences of the evaluating team.

Keywords

machinery replacement; engineering economy; FUCOM; TOPSIS; sensitivity analysis.

Downloads

References

1. AISD. (2026). N8N workflows for order intake and inventory synchronization: Case studies. AISD Technical Reports. [Google Scholar] [Crossref]

2. Bettiol, M., Capestro, M., Di Maria, E., & Micelli, S. (2022). Disentangling the link between ICT and Industry 4.0: Impacts on knowledge-intensive business services. International Journal of Production Economics, 247, Article 108460. https://doi.org/10.1016/j.ijpe.2022.108460 [Google Scholar] [Crossref]

3. Bigliardi, B., Bottani, E., Casella, G., Filippelli, S., Petroni, A., & Pini, B. (2026). Artificial intelligence in SME supply chains: A bibliometric and case study analysis. Procedia Computer Science. [Google Scholar] [Crossref]

4. Cirillo, V., Fanti, L., Mina, A., & Ricci, A. (2023). Digitalization and productivity: The role of organizational capabilities. Industrial and Corporate Change. [Google Scholar] [Crossref]

5. Culot, G., Podrecca, M., & Nassimbeni, G. (2024). Artificial intelligence in supply chain management: A systematic literature review of empirical studies and research directions. Computers in Industry, 162, Article 104132. https://doi.org/10.1016/j.compind.2024.104132 [Google Scholar] [Crossref]

6. Diario de México. (2026, March 15). Growth in the use of artificial intelligence in Mexican logistics. Diario de México. [Google Scholar] [Crossref]

7. Diractum. (2025). Productivity reports on 3D printing for Mexican firms. Diractum. [Google Scholar] [Crossref]

8. Ecosistema Startup. (2026). Digital maturity report of SMEs in Mexico 2026. Ecosistema Startup. [Google Scholar] [Crossref]

9. Frazier, W. E., et al. (2024). Data management strategies for additive manufacturing adoption in SMEs. Additive Manufacturing, 72. [Google Scholar] [Crossref]

10. García, A., López, M., & Hernández, R. (2025). Integrated value and supply chain model to boost the competitiveness of SMEs in the municipality of Mixquiahuala de Juárez, Hidalgo. Revista de Gestão Social e Ambiental, 19(3), 1–15. [Google Scholar] [Crossref]

11. Haug, A., Adsbøll Wickstrøm, K., Stentoft, J., & Philipsen, K. (2023). The adoption of additive manufacturing and AI in SMEs: Barriers and enablers. Journal of Manufacturing Technology Management. [Google Scholar] [Crossref]

12. Hernández Díaz, A., et al. (2026). Artificial intelligence in the management of supply chains of Mexican SMEs. Revista de Ingeniería Industrial. [Google Scholar] [Crossref]

13. Hernández Vega, L. (2026). Barriers to AI adoption in Mexican SMEs. Ecosistema Startup Report. [Google Scholar] [Crossref]

14. INEGI. (2024). Economic Censuses 2024: Timely results. Instituto Nacional de Estadística y Geografía. [Google Scholar] [Crossref]

15. KPMG México. (2026). Nearshoring and digital transformation in the Mexican supply chain. KPMG. [Google Scholar] [Crossref]

16. Marzi, G., et al. (2020). Additive manufacturing in Italian SMEs: Evidence from empirical studies. Technovation, 92–93. [Google Scholar] [Crossref]

17. McConnell, S., et al. (2024). Productivity improvements in powder bed fusion metal additive manufacturing: A systematic literature review. Journal of Manufacturing Processes, 110, 250–265. [Google Scholar] [Crossref]

18. Mohedano Torres, E. de J., Hernández Islas, J., Chiapa Tellez, F. A., Aguilar Pérez, N., & Soní Ramírez, K. S. (2026). Implementation of an intelligent supply management system in a Mexican SME using N8N. Revista NeyArt, 4(1). https://doi.org/10.61273/neyart.v4i1.165 [Google Scholar] [Crossref]

19. OECD. (2019). OECD territorial reviews: Hidalgo, Mexico. OECD Publishing. https://doi.org/10.1787/9789264303490-en [Google Scholar] [Crossref]

20. OECD. (2026). OECD economic surveys: Mexico 2026. OECD Publishing. [Google Scholar] [Crossref]

21. Onorio, P. O., Frazzon, E. M., Leusin, M. E., Cordes, C., & Azevedo, V. (2026). Artificial intelligence supporting human intelligence: Impacts on supply chains of small and medium enterprises. Procedia Computer Science, 277, 2485–2494. [Google Scholar] [Crossref]

22. Page, M. J., McKenzie, J. E., Bossuyt, P. M., Boutron, I., Hoffmann, T. C., Mulrow, C. D., Shamseer, L., Tetzlaff, J. M., Akl, E. A., Brennan, S. E., Chou, R., Glanville, J., Grimshaw, J. M., Hróbjartsson, A., Lalu, M. M., Li, T., Loder, E. W., Mayo-Wilson, E., McDonald, S., … Moher, D. (2021). The PRISMA 2020 statement: An updated guideline for reporting systematic reviews. BMJ, 372, Article n71. https://doi.org/10.1136/bmj.n71 [Google Scholar] [Crossref]

23. Rogers, E. M. (2003). Diffusion of innovations (5th ed.). Free Press. [Google Scholar] [Crossref]

24. Saci, A. (2026). Low-code automation with N8N and AI agents for inventory cycle counting in Latin American SMEs. Journal of Supply Chain Automation. [Google Scholar] [Crossref]

25. Saldana-Robles, A., et al. (2019). Insertion of low-cost additive manufacturing in engineering education. Revista de Ingeniería Educativa, 15(2), 112–125. [Google Scholar] [Crossref]

26. Sæterbø, M., & Solvang, W. D. (2024). Adoption matrix for metal additive manufacturing in SMEs. Procedia CIRP, 120, 450–455. [Google Scholar] [Crossref]

27. Suárez, J., & Romero, L. (2024). Productivity in additive manufacturing farms vs. injection in low volume. Ingeniería Industrial, 42(1), 67–80. [Google Scholar] [Crossref]

28. Toorajipour, R., Sohrabpour, V., Nazarpour, A., Oghazi, P., & Fischl, M. (2021). Artificial intelligence in supply chain management: A systematic literature review. Journal of Business Research, 122, 502–517. https://doi.org/10.1016/j.jbusres.2020.09.009 [Google Scholar] [Crossref]

29. Varela Insights. (2026). N8N implementations in Latin American SMEs: Productivity results. Varela Insights Report. [Google Scholar] [Crossref]

30. Vázquez Rojas, A. R., et al. (2016). Analysis of total factor productivity in the state of Hidalgo. Revista de Economía Regional. [Google Scholar] [Crossref]

Metrics

Views & Downloads

Similar Articles