Development and Preliminary Evaluation of a Poka-Yoke Support Hook for Brake Calipers During Brake Pad Replacement
Authors
Héctor Luis Gutiérrez Martínez
Industrial Design Engineering, Instituto Tecnológico de Pachuca, Pachuca, Hidalgo, Mexico (Mexico)
Industrial Design Engineering, Instituto Tecnológico de Pachuca, Pachuca, Hidalgo, Mexico (Mexico)
Industrial Design Engineering, Instituto Tecnológico de Pachuca, Pachuca, Hidalgo, Mexico (Mexico)
Industrial Design Engineering, Instituto Tecnológico de Pachuca, Pachuca, Hidalgo, Mexico (Mexico)
Industrial Design Engineering, Instituto Tecnológico de Pachuca, Pachuca, Hidalgo, Mexico (Mexico)
Industrial Design Engineering, Instituto Tecnológico de Pachuca, Pachuca, Hidalgo, Mexico (Mexico)
Article Information
DOI: 10.47772/IJRISS.2026.102500014
Subject Category: Education
Volume/Issue: 10/25 | Page No: 290-303
Publication Timeline
Submitted: 2026-10-26
Accepted: 2026-10-31
Published: 2026-11-14
Abstract
Temporarily supporting a removed brake caliper is a necessary part of brake maintenance because the hydraulic hose must not serve as a suspension element. This study examines the design of a caliper support hook made from AISI 1020 steel and interprets the graphical evidence from a static simulation. An applied case study was conducted, integrating a documentary review, an exploratory literature search guided by PRISMA transparency criteria, failure mode and effects analysis (FMEA), and interpretation of four numerical plots and one material data sheet. The model shown contains two hooks, perforated arms, joints, and a diagonal bar. The plot scales show upper limits of 36.56 MPa for von Mises equivalent stress, 0.1925 mm for resultant displacement, and 1.339 × 10⁻⁴ for equivalent strain. The visible distribution concentrates higher stress and strain near the upper-hook transition, while displacement increases toward the loaded lower end. The AISI 1020 data sheet indicates a yield strength of 351.571 MPa, consistent with the displayed minimum factor of safety of approximately 9.6. However, load, contact, and mesh-convergence documentation is missing, so no allowable capacity is established. FMEA ranks unintended disengagement as the highest internal priority, a condition that the structural plot does not verify. The 10.0- and 8.8-minute values represent a projected 12% reduction, not workshop measurements. Improvements to the geometric transition, retention, and joint modeling are proposed, together with a verification plan. No physical prototype exists; drawings remain pending, and an illustrative render is included. The contribution is to connect the available numerical results with design decisions and explicit limits on interpretation.
Keywords
Poka-Yoke; brake caliper; AISI 1020 steel; FMEA; brake pad replacement.
Downloads
References
1. Autodesk. (n.d.). Mesh convergence. Fusion Simulation Help. https://help.autodesk.com/cloudhelp/ENU/Fusion-Simulate/files/SIM-MESH-CONVERGENCE.htm [Google Scholar] [Crossref]
2. Automotive Industry Action Group. (2019, June 13). New AIAG & VDA FMEA handbook and trainings available! https://blog.aiag.org/new-aiag-vda-fmea-handbook-and-trainings-available [Google Scholar] [Crossref]
3. Dassault Systèmes. (2012). Output of linear static analysis. SOLIDWORKS Design Help. https://help.solidworks.com/2012/English/SolidWorks/cworks/IDH_Analysis_Background_Output_of_Static_Analysis.htm [Google Scholar] [Crossref]
4. Dassault Systèmes. (2016). Maximum von Mises stress criterion. SOLIDWORKS Design Help. https://help.solidworks.com/2016/English/SolidWorks/cworks/r_Maximum_von_Mises_Stress_Criterion.htm [Google Scholar] [Crossref]
5. Caliper Hook Project Team. (2026). Simulaacion estatica [Unpublished five-page updated PDF containing simulation results and material data sheet]. https://drive.google.com/file/d/1f15XEuOlbg8hX1eDO5kp9YfZFnTrObJ2/view [Google Scholar] [Crossref]
6. HELLA. (n.d.). Changing brake pads, brake discs and brake calipers. HELLA Tech World. https://www.hella.com/techworld/us/technical/brakes/changing-brake-pads-brake-discs-and-brake-calipers/ [Google Scholar] [Crossref]
7. Kamicase Team. (n.d.-a). AMEF_Disenio_Gancho_Porta_Caliper [Unpublished design FMEA, revision 1.0]. Instituto Tecnológico de Pachuca. [Google Scholar] [Crossref]
8. Kamicase Team. (n.d.-b). Diseño de Experimentos – Gancho Poka-Yoke-3 [Unpublished presentation]. Instituto Tecnológico de Pachuca. [Google Scholar] [Crossref]
9. Kamicase Team. (n.d.-c). Producción más limpia Poka-Yoke [Unpublished Cleaner Production report]. Instituto Tecnológico de Pachuca. [Google Scholar] [Crossref]
10. Lazarevic, M., Mandic, J., Sremcev, N., Vukelic, D., & Debevec, M. (2019). A systematic literature review of Poka-Yoke and novel approach to theoretical aspects. Strojniški vestnik – Journal of Mechanical Engineering, 65(7–8), 454–467. https://doi.org/10.5545/sv-jme.2019.6056 [Google Scholar] [Crossref]
11. Packer, T. (n.d.). SOLIDWORKS Simulation: An explanation of the global contact option. SOLIDWORKS Blog. https://blogs.solidworks.com/products/solidworks/solidworks-simulation-explanation-global-contact-option/ [Google Scholar] [Crossref]
12. PRISMA statement. (n.d.-a). PRISMA 2020 statement. https://www.prisma-statement.org/prisma-2020 [Google Scholar] [Crossref]
13. PRISMA statement. (n.d.-b). PRISMA extension for scoping reviews. https://www.prisma-statement.org/scoping [Google Scholar] [Crossref]
14. Shingo, S. (1985). A revolution in manufacturing: The SMED system. Productivity Press. [Google Scholar] [Crossref]
15. Shingo, S. (1986). Zero quality control: Source inspection and the Poka-Yoke system. Productivity Press. [Google Scholar] [Crossref]
16. Vidor, G., & Saurin, T. A. (2011). Conceitos e características de sistemas poka-yokes: uma revisão de literatura. Revista Produção Online, 11(2), 344–368. https://doi.org/10.14488/1676-1901.v11i2.644 [Google Scholar] [Crossref]
17. Visser, M. (n.d.). What is a stress singularity in SOLIDWORKS Simulation? SOLIDWORKS Blog. https://blogs.solidworks.com/products/solidworks/what-is-a-stress-singularity-in-solidworks-simulation/ [Google Scholar] [Crossref]
18. voestalpine High Performance Metals. (n.d.). AISI 1020 [Información técnica de producto]. https://www.voestalpine.com/highperformancemetals/australia/en-au/products/aisi-1020/ [Google Scholar] [Crossref]
Metrics
Views & Downloads
Similar Articles
- Assessment of the Role of Artificial Intelligence in Repositioning TVET for Economic Development in Nigeria
- Teachers’ Use of Assure Model Instructional Design on Learners’ Problem Solving Efficacy in Secondary Schools in Bungoma County, Kenya
- “E-Booksan Ang Kaalaman”: Development, Validation, and Utilization of Electronic Book in Academic Performance of Grade 9 Students in Social Studies
- Analyzing EFL University Students’ Academic Speaking Skills Through Self-Recorded Video Presentation
- Major Findings of The Study on Total Quality Management in Teachers’ Education Institutions (TEIs) In Assam – An Evaluative Study